manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 224

system misinterpreting a close object as a sensor

problem, causing the “PARKSENSE UNAVAILABLE

SERVICE REQUIRED” message to be displayed in the

instrument cluster.

CAUTION!

•

ParkSense® is only a parking aid and it is unable to
recognize every obstacle, including small obstacles.
Parking curbs might be temporarily detected or not
detected at all. Obstacles located above or below
the sensors will not be detected when they are in
close proximity.

•

The vehicle must be driven slowly when using
ParkSense® in order to be able to stop in time
when an obstacle is detected. It is recommended
that the driver looks over his/her shoulder when
using ParkSense®.

WARNING!

•

Drivers must be careful when backing up even
when using ParkSense®. Always check carefully
behind your vehicle, look behind you, and be sure
to check for pedestrians, animals, other vehicles,
obstructions, and blind spots before backing up.
You are responsible for safety and must continue to
pay attention to your surroundings. Failure to do so
can result in serious injury or death.

(Continued)

222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands