Chapter 15
15-16
15.3.2 Error Codes
0009-7942
T-15-7
The combination of characters used in the search
condition fails to make up a correct search condition.
There must be as many "s as there are "s
The symbol * is not included within parentheses.
Check to be sure that the combination of characters is in
keeping with the rule; then, try once again.
If LDAP of the server and the character code is version
2 (JIS), there is a character that is not part of the ASCII
code (0x20-0x7E).
Remove any character that cannot be used; then, try
once gain.
The version setting of the server is wrong, and the search cannot be initiated. Check the settings.
In user mode, the LDAP server settings (server LDAP
version and character code) is set for version 3;
however, the LDAP server is operating for version 2.
In user mode, set the LDAP server settings so that the
LDAP server version and the character code are both
version 2.
Cause
Remedy
# 001
There is a paper or original jam.
Remove the jammed paper or original.
# 003
A communication lasting longer than a specific period of
time (64 min) will cause an error state.
1. Decrease the resolution for transmission.
2. In the case of reception, ask the source to decrease the
resolution or divide the original.
# 005
The target does not respond within 35 sec.
Check to be sure that the target is ready to communicate;
then, try once again.
The target is a non-G3 model.
Check the target.
# 009
There is no paper.
Supply paper.
The cassette is not fitted properly.
Fit the cassette correctly.
# 011
The original to be transmitted is not placed properly.
Start over from the beginning.
# 012
The target is out of recording paper, and transmission
has failed.
Ask the target to supply recording paper.
# 018
There is no response to a redial attempt.
Check to make sure that the target is ready for
communication; then, try once again.
The target is engaged for a different communication, and
transmission has failed.
Check to make sure that the target is ready for
communication; then, try once again.
The settings do not match the settings of the target, and
the transmission has failed.
Check to make sure that the target is ready for
communication; then, try once again.
# 022
The particulars of the group address selected as the
forwarding target may have been deleted, or there is no
more than a user box, thus causing the transmission to
fail.
Try transmitting once again.
The attempt to transmit to an address registered in the
address book has failed because the address has been
removed from the address table while in wait for
transmission.
Try once again.
# 037
There is a shortage of memory, not permitting reception. Remove error files and unnecessary files to increase
available memory.
# 080
F code is not set on the target.
Check the F code of the target, and start over.
# 081
The appropriate password is not set on the target.
Check the password of the target, and start over.
# 099
The transmission has been suspended in the middle.
Start over.
# 102
There is a mismatch of F code or password.
Check the F code and the password of the target, and
start over.
# 107
Cause
Remedy
Summary of Contents for iR5570 Series
