manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

Using a Battery Charger............................................1-40

Battery Installation and Connection..................................1-41
Storage.............................................................................1-42
Maintaining Charge..........................................................1-42

1.17 STEERING HEAD BEARINGS

General.............................................................................1-44
Inspection.........................................................................1-44
Determining Proper Resistance.......................................1-44

1.18 FRONT FORK OIL REPLACEMENT

General.............................................................................1-45
Procedure.........................................................................1-45

1.19 HEADLAMP

Headlamp Alignment........................................................1-46
Headlamp Adjustment: Firebolt........................................1-46
Headlamp Adjustment: Lightning......................................1-47

Horizontal Alignment.................................................1-47
Vertical Alignment.....................................................1-47

Headlamp Adjustment: Ulysses........................................1-47

Horizontal Alignment.................................................1-47
Vertical Alignment.....................................................1-48

1.20 WINDSHIELD MAINTENANCE

General.............................................................................1-49

1.21 STORAGE

General.............................................................................1-50
Removal From Storage.....................................................1-50

1.22 TROUBLESHOOTING

General.............................................................................1-51
Engine..............................................................................1-51

Starter Motor Does Not Operate or Does Not Turn Engine
Over...........................................................................1-51
Engine Turns Over But Does Not Start......................1-51
Starts Hard................................................................1-51
Starts But Runs Irregularly or Misses........................1-51
Spark Plug Fouls Repeatedly....................................1-51
Pre-Ignition or Detonation (Knocks or Pings)............1-52
Overheating...............................................................1-52
Valve Train Noise.......................................................1-52
Excessive Vibration...................................................1-52
Check Engine Light Illuminates During Operation.....1-52

Lubrication System...........................................................1-52

Oil Does Not Return To Oil Tank................................1-52
Engine Uses Too Much Oil Or Smokes Excessively...1-52
Engine Leaks Oil From Cases, Push Rods, Hoses,
Etc.............................................................................1-52
Low Oil Pressure.......................................................1-52
High Oil Pressure......................................................1-53

Electrical System..............................................................1-53

Alternator Does Not Charge......................................1-53
Alternator Charge Rate Is Below Normal..................1-53
Speedometer Operates Erratically............................1-53

Transmission.....................................................................1-53

Shifts Hard................................................................1-53
Jumps Out Of Gear...................................................1-53
Clutch Slips...............................................................1-53
Clutch Drags Or Does Not Release..........................1-53

Clutch Chatters..........................................................1-53

Clutch...............................................................................1-53

Slips..........................................................................1-53
Drags or Does Not Release......................................1-53
Chatters.....................................................................1-53

Chassis.............................................................................1-53

Irregular/Inadequate Brake Action.............................1-53
Handling Irregularities...............................................1-53

Suspension.......................................................................1-54

CHASSIS

2.1 FASTENER TORQUE VALUES

Fastener Torque Values in this Chapter..............................2-1

2.2 SPECIFICATIONS

Firebolt.............................................................................2-11
Lightning...........................................................................2-12
Ulysses.............................................................................2-13
Suspension Settings.........................................................2-15

2.3 VEHICLE IDENTIFICATION NUMBER
(VIN)

Vehicle Identification Number (V.I.N.)...............................2-19

2.4 WHEELS

General.............................................................................2-21
Troubleshooting................................................................2-21

2.5 FRONT WHEEL

Removal...........................................................................2-23
Disassembly.....................................................................2-23

Bearing Removal.......................................................2-23
Front Rotor Removal.................................................2-25

Cleaning and Inspection...................................................2-25
Assembly..........................................................................2-26

Bearing Installation....................................................2-26
Front Rotor Installation..............................................2-29

Installation........................................................................2-29

2.6 REAR WHEEL

Removal...........................................................................2-31
Cleaning and Inspection...................................................2-31
Repair...............................................................................2-31

Inspection..................................................................2-31
Drive Sprocket...........................................................2-31
Brake Rotor...............................................................2-32

Disassembly.....................................................................2-32
Wheel Bearings: Two Bearing Wheels..............................2-34

Removal....................................................................2-34
Installation: Rotor Side Bearing.................................2-35
Installation: Opposite Side Bearing...........................2-36

Wheel Bearings: Three Bearing Wheels...........................2-37

Removal: Brake Rotor Side.......................................2-37
Removal: Sprocket Side............................................2-39
Installation: Brake Rotor Side....................................2-39
Installation: Sprocket Side.........................................2-40

Installation........................................................................2-41

IV TABLE OF CONTENTS

TABLE OF CONTENTS

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Gentex CVC M9 Operation And Maintenance Manual preview
CVC M9
Brand: Gentex Pages: 15
Takegawa TwinSpark Super head plus R Instruction Manual preview
TwinSpark Super head plus R
Brand: Takegawa Pages: 5
BMW K 1200RS Repair Manual preview
K 1200RS
Brand: BMW Pages: 416
Ohlins HO 1072 Mounting Instructions preview
HO 1072
Brand: Ohlins Pages: 2
hepco & becker 5039505 00 01 Quick Start Manual preview
5039505 00 01
Brand: hepco & becker Pages: 2
hepco & becker 630296 00 01 Manual preview
630296 00 01
Brand: hepco & becker Pages: 4
hepco & becker 6304541 00 02 chrom Assembling Instructions preview
6304541 00 02 chrom
Brand: hepco & becker Pages: 6
DYNATEK DDK2-18C Installation Manual preview
DDK2-18C
Brand: DYNATEK Pages: 12
Buell N1050.1AK Instruction Sheet preview
N1050.1AK
Brand: Buell Pages: 9
Sealey VS779.V3 Instructions preview
VS779.V3
Brand: Sealey Pages: 2
Arrow Kawasaki NINJA 650 Fitting Instructions Manual preview
Kawasaki NINJA 650
Brand: Arrow Pages: 7
Petzl Vertex Best Duo Manual preview
Vertex Best Duo
Brand: Petzl Pages: 17
KTM 250 EXC Six Days TPI Owner'S Manual preview
250 EXC Six Days TPI
Brand: KTM Pages: 180
Harbor Freight Tools 94830 Assembly Instructions Manual preview
94830
Brand: Harbor Freight Tools Pages: 9
HealTech Electronics GIpro w/ATRE User Manual preview
GIpro w/ATRE
Brand: HealTech Electronics Pages: 4
zeeltronic PDCI-11VT User Manual preview
PDCI-11VT
Brand: zeeltronic Pages: 17
ICARO 2000 Solar X 2 Owner'S Manual preview
Solar X 2
Brand: ICARO 2000 Pages: 15
MAEVING RM1 Owner'S Handbook Manual preview
RM1
Brand: MAEVING Pages: 84

Brands by name

Popular brands

Load more brands