manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

2.38

INTAKE COVER

REMOVAL

NOTE

See 

Figure 2-187

. The X-Guard (1) on XB9SX and XB12SX

models is a non-replaceable part.

1.

Remove seat.

2.

Remove the rear fasteners and nylon washers (3).

NOTE

Models with a translucid intake cover use a top hat bushing
and two isolating washers for each front fastener (5). Other
models with molded in color use a nylon washer with each front
fastener (4).

3.

Remove front fasteners.

a.

On models with a translucid intake cover, remove
front fasteners with top hat bushings and isolator
washers (5).

b.

On other models (with molded in color), remove front
fasteners and nylon washers (4).

4.

Remove intake cover assembly (2).

INSTALLATION

1.

See 

Figure 2-187

. Position intake cover assembly (2) over

top of air cleaner cover.

NOTE

Front fasteners are installed at a slight angle.

2.

Loosely install front fasteners (4, 5).

a.

On models with a translucid intake cover, start the
two front fasteners with top hat bushings and isolator
washers (5).

b.

On other models (with molded in color), start the two
front fasteners with nylon washers (4).

3.

Install the rear fasteners and nylon washers (3). Tighten
all fasteners to 12-36 in-lbs (1.4-4 Nm).

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

4.

Install seat.

HOME

2010 XB Service: Chassis  2-139

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Fantic Motor 125 Series Owner'S Manual preview
125 Series
Brand: Fantic Motor Pages: 130
Öhlins SD 047 Mounting Instruction preview
SD 047
Brand: Öhlins Pages: 8
Öhlins prodrive SUR 3A00 Mounting Instructions preview
prodrive SUR 3A00
Brand: Öhlins Pages: 4
Öhlins HO 404 Mounting Instructions preview
HO 404
Brand: Öhlins Pages: 2
Öhlins HO 201 Owner'S Manual preview
HO 201
Brand: Öhlins Pages: 2
Öhlins FCX 0302 Mounting Instructions preview
FCX 0302
Brand: Öhlins Pages: 8
Öhlins DU 907 Mounting Instructions preview
DU 907
Brand: Öhlins Pages: 4
Qlink LG250 User Manual preview
LG250
Brand: Qlink Pages: 44
Suzuki DR-Z70 Service Manual preview
DR-Z70
Brand: Suzuki Pages: 199
Dennis Kirk Scorpion Exo-T520 Tech Manual preview
Scorpion Exo-T520
Brand: Dennis Kirk Pages: 10
Denali MA11729 Manual preview
MA11729
Brand: Denali Pages: 5
Isotta SP8106 R1200R Fitting Instructions preview
SP8106 R1200R
Brand: Isotta Pages: 2
Yamaha MWS150-C Owner'S Manual preview
MWS150-C
Brand: Yamaha Pages: 98
Yamaha NIKEN 2019 Owner'S Manual preview
NIKEN 2019
Brand: Yamaha Pages: 116
Yamaha Tracer 9 GT 2021 Manual preview
Tracer 9 GT 2021
Brand: Yamaha Pages: 126
Yamaha NIKEN GT 2021 Owner'S Manual preview
NIKEN GT 2021
Brand: Yamaha Pages: 116
Yamaha TRACER 7 Owner'S Manual preview
TRACER 7
Brand: Yamaha Pages: 106
Yamaha MXT9L 2019 Manual preview
MXT9L 2019
Brand: Yamaha Pages: 116

Brands by name

Popular brands

Load more brands