Buell XB 2010 Service Manual Download Page 533 | Manualshive

Page: 533 / 714

background image

4

3

2

1

5

sm00453

1.

Jam nuts with washers (2)

2.

Center tail section

3.

Screws (2)

4.

Lamp lens

5.

License plate lamp

Figure 6-69. License Plate Lamp: Lightning

ULYSSES

Removal and Disassembly

1.

Remove seat.

2.

See

. Remove the cover for the rear wiring (3).

3.

Disconnect the two connectors [45] from license plate
lamp harness.

4.

Pull the lamp assembly away from license plate bracket
(1) pulling the harness out of the license plate bracket.

Assembly and Installation

1.

See

. Install new license plate lamp assembly.

a.

Insert license plate lamp wiring harness through hole
and route into the center tail section (2) and the
license plate bracket (4).

b.

Attach the two connectors [45] from license plate lamp
to main harness.

c.

Attach lamp (3) and wire cover (5) to tail section using
washers and jam nuts (1) and tighten to 12-36 in-lbs
(1.4-4 Nm).

d.

. Attach front of wire cover by

installing remaining fasteners (6) and tightening to
36-48 in-lbs (4.1-5.4 Nm).

2.

Check lamp for proper operation. If operation fails, reread
procedure and verify that all steps were performed.

a.

Turn ignition key switch to ON.

b.

Check for license plate lamp illumination.

c.

Turn ignition key switch to OFF.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

3.

Install seat.

1

2

3

sm00450

1.

Center tail section

2.

License plate bracket

3.

Cover, rear wiring

Figure 6-70. License Plate Lamp Mounting: Ulysses

2010 XB Service: Electrical 6-59

«
...
531
532
533
534
535
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: R&G Pages: 13

Brand: GYS Pages: 36

TMAX ABS Series

Brand: Yamaha Pages: 122

Tenere 700 2024

Brand: Yamaha Pages: 110

Brand: Baja motorsports Pages: 20

Brand: DYNATEK Pages: 8

Brand: Smarter tools Pages: 28

Brand: Singing rock Pages: 2

HelmetTalk HTCS-3O

Brand: Nady Systems Pages: 2

Rumbler 500 2017

Brand: Royal Enfield Pages: 160

Brand: Wunderlich Pages: 2

Brand: Power Fist Pages: 4

Brand: RIEJU Pages: 147

Brand: Denali Pages: 3

Brand: Petzl Pages: 14

Brand: APRILIA Pages: 264

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands