Buell XB 2010 Service Manual Download Page 340 | Manualshive

Page: 340 / 714

background image

3.14

OIL PRESSURE INDICATOR SWITCH

GENERAL

The oil pressure indicator switch is a pressure-actuated dia-
phragm-type switch. When oil is not circulating through the
system or when oil pressure is low, spring tension holds the
switch contacts closed, thereby completing the signal light cir-
cuit and causing the indicator lamp to illuminate.

OIL PRESSURE SIGNAL LIGHT

The oil pressure signal light turns ON when:

•

Ignition switch is turned on prior to starting engine.

•

Oil is not circulating through the running engine.

•

Oil pressure is abnormally low in the running engine.

•

Engine is idling below 1000 RPM.

The oil pressure signal light turns OFF when:

•

Oil is circulating with adequate pressure through the
engine running at 1000 RPM or greater.

Troubleshooting information is listed in

.

NOTE

If the ignition is turned back on immediately after the engine
is stopped, the oil light may not turn on right away because of
oil pressure retained in the filter housing.

OIL PRESSURE

TOOL NAME

PART NUMBER

OIL PRESSURE GAUGE SET

HD-96925-52B

1.

See

. Unplug connector from oil pressure

indicator lamp switch located under the oil pump next to
the oil filter mount, unscrew and remove oil pressure switch
from crankcase.

2.

. Install adapter (2) from OIL PRESSURE

GAUGE SET (Part No. HD-96925-52B) in oil pressure
indicator lamp switch mounting hole. Tighten adapter
snugly. DO NOT OVERTIGHTEN.

sm03000

Figure 3-100. Oil Pressure Indicator Switch

Table 3-22. Troubleshooting Oil Pressure Signal Lamp

PROBABLE CAUSES

OIL PRESSURE
SIGNAL LAMP

Empty oil reservoir

Stays on at speeds
above idle

Grounded oil switch wire

Malfunctioning signal switch

Diluted oil

Malfunctioning or improperly installed
pressure relief valve

Oil sieve clogged

Incorrect idle speed

Flickers at idle

Malfunctioning or improperly installed
pressure relief valve

Malfunctioning signal switch

Does not glow
when ignition is
turned on (prior to
operating engine)

Malfunction in wiring

Burned-out signal bulb

Dead battery

3.

Assemble banjo bolt (3), washer (4), oil pressure gauge
(1) banjo fitting and second washer onto adapter and
tighten snugly.

4.

Temporarily secure oil pressure gauge and hose to
motorcycle frame with cable straps. Make sure gauge and
hose assembly do not interfere with normal operation of
the vehicle. Start engine and ride motorcycle at least 20
miles (32 km) at or above 50 mph (80 km/h) to allow

3-72 2010 XB Service: Engine

«
...
338
339
340
341
342
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: Caberg Pages: 16

Brand: Honda Pages: 112

Brand: Yamaha Pages: 662

Brand: KTM Pages: 130

Brand: RDMOTO Pages: 2

Brand: BMW Motorrad Pages: 261

Brand: SCA Pages: 5

Brand: Aim Pages: 5

Brand: hepco & becker Pages: 6

Scorpion 608-30-10086

Brand: Barnett Pages: 2

Spyder ST Limited SE5

Brand: Can-Am Pages: 41

Brand: Cagiva Pages: 407

MS3 - CATALOGUE

Brand: HYOSUNG Pages: 104

Brand: Oxford Pages: 40

HotGrips OF690 Adventure

Brand: Oxford Pages: 42

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 192

Brand: Honda Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands