Buell XB 2010 Service Manual Download Page 123

Page: 123 / 714

Table 2-21. Tires: 2010 XB Models

ALL LOADS TO GVWR

SIZE

APPROVED BRAND

FRONT/REAR

MODEL

kPa

psi

234

120/70 ZR 17

Pirelli Scorpion SYNC

Front

XB12Ss
XB12Scg

248

180/55 ZR 17

Pirelli Scorpion SYNC

Rear

234

120/70 ZR 17

Pirelli Diablo Angel ST

Front

XB12XT

248

180/55 ZR 17

Pirelli Diablo Angel STE

Rear

DISMOUNTING

Remove the wheel.

Deflate the tire.

See

Figure 2-44

. Use the tire machine to loosen both tire

beads from the rim flange.

See

Figure 2-45

. Push the lower bead into the rim well on

one side and insert tire tool underneath the bead from the
opposite side.

Pry the bead over the rim edge. Remove the tire from the
rim.

sm00113

Figure 2-44. Loosening Beads from Rim Flange

sm00114

Figure 2-45. Pry Bead Over Rim Edge

CLEANING AND INSPECTION

TOOL NAME

PART NUMBER

TIRE SPREADER

HD-21000

Mount tire on TIRE SPREADER (Part No. HD-21000) for
cleaning and inspection.

Clean inside of tire with dry rag.

If rim is dirty or corroded, clean with a stiff wire brush.

Inspect tire for wear and damage. Replace worn or dam-
aged tires.

HOME

2010 XB Service: Chassis 2-43

Summary of Contents for XB 2010










































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands

Buell XB 2010, Service Manual

Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands