Buell XB 2010 Service Manual Download Page 281 | Manualshive

Page: 281 / 714

background image

sm04534

Figure 3-4. Throttle cable elbow alignment

13. Tighten the throttle cable jamnuts to 36-40 in-lbs (4-4.5

Nm).

14. Install the ignition coil (1) and coil connection [83] (2) and

tighten fasteners to 120-144 in-lbs (13.6-16.3 Nm).

15. Attach plastic clip (3) securing the coil wire to the throttle

cable bracket.

NOTE

Remove shop towel from entrance of throttle body to verify
proper operation of induction module.

16. Connect fuel line (7).

17. Install throttle body velocity stack with retaining ring.

18. Install air filter base plate. See

4.3 AIR CLEANER

.

19. Install muffler. See

4.19 EXHAUST SYSTEM

NOTES

•

Due to the location of the CKP it will be necessary to align
the Torca clamp to verify proper clearance between the
chin fairing and the CKP and Torca clamp.

•

For 1200 model motorcycles with interactive exhaust
systems see

6.16 INTERACTIVE EXHAUST SYSTEM

.

20. Install idler pulley. See

5.7 DRIVE BELT AND IDLER

21. Install left and right side rider footpeg mount. See

2.34 FOOTPEG, HEEL GUARD AND MOUNT: FIREBOLT
AND LIGHTNING MODELS

2.35 HEEL GUARD AND

FOOTPEG MOUNTS: ULYSSES MODELS

.

22. Install sprocket cover. See

2.36 SPROCKET COVER

.

NOTE

When installing the left side air scoop it is necessary to verify
that the voltage regulator and alternator wiring harnesses are
not trapped between the air scoop and cylinder head.

23. Connect front oxygen sensor connector and secure in

retainer on right-inner air scoop housing. Verify split con-
duit is in place on sensor wire. Install air scoops, right and
left sides. See

2.49 AIR SCOOPS

.

NOTE

The connection for fuel pump is just above the pump located
at the rear of the fuel tank on the left side of the vehicle.

24. Connect fuel pump. See

.

25. Install intake cover. See

2.38 INTAKE COVER

26. Connect negative ground cable to battery and tighten

fastener to 60-70 in-lbs (6.8-7.9 Nm).

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

27. Install seat.

28. Remove motorcycle from lift.

29. Install chin fairing. See

2.50 CHIN FAIRING

2010 XB Service: Engine 3-13

«
...
279
280
281
282
283
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: N-Com Pages: 28

Brand: N-Com Pages: 2

Brand: Honda Pages: 141

Brand: R&G Pages: 47

Brand: hepco & becker Pages: 4

Brand: Zero Pages: 162

Brand: Honda Pages: 60

Brand: kellermann Pages: 2

Brand: hepco & becker Pages: 5

Brand: PIAGGIO Pages: 8

Brand: R&G Pages: 13

Brand: BMW Pages: 241

Brand: Shark Pages: 18

factor-x-rearset.gt

Brand: gilles.tooling Pages: 4

Brand: RIEJU Pages: 280

Brand: Ermax Pages: 2

Brand: Dräger Pages: 256

SPIDER MAX GT 500

Brand: Malaguti Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands