Buell XB 2010 Service Manual Download Page 12

Page: 12 / 714

Installation: Firebolt..........................................................2-90
Removal: Lightning/Ulysses.............................................2-91
Installation: Lightning/Ulysses..........................................2-91

2.18 STEERING HEAD BEARINGS

Removal...........................................................................2-93
Installation........................................................................2-93

2.19 SWINGARM AND BRACE

General.............................................................................2-96
Brace................................................................................2-96

Removal....................................................................2-96
Installation.................................................................2-96

Removal: Swingarm..........................................................2-96
Disassembly.....................................................................2-97

Swingarm..................................................................2-97

Cleaning and Inspection...................................................2-97
Assembly..........................................................................2-98

Swingarm..................................................................2-98

Installation: Swingarm......................................................2-98

2.20 FRONT AND REAR ISOLATORS

Front Isolator..................................................................2-100

Removal..................................................................2-100
Installation...............................................................2-100

Rear Isolator...................................................................2-100

2.21 FRAME PUCKS

Removal.........................................................................2-101
Installation......................................................................2-101

2.22 FRAME

Removal.........................................................................2-103
Installation......................................................................2-103

2.23 REAR SHOCK ABSORBER

2.24 THROTTLE CONTROL

Removal and Disassembly.............................................2-110
Cleaning and Inspection.................................................2-110
Assembly and Installation...............................................2-110
Throttle Cable Replacement...........................................2-111

Removal..................................................................2-111
Installation...............................................................2-111

2.25 CLUTCH CONTROL

General...........................................................................2-113
Removal and Disassembly.............................................2-113

Clutch Cable............................................................2-113

Assembly and Installation...............................................2-115

Clutch Cable............................................................2-115

2.26 HEADLAMP ASSEMBLY AND
SUPPORT BRACKET

2.27 FAIRING SUPPORT BRACKET:
FIREBOLT

Removal.........................................................................2-123
Installation......................................................................2-123

2.28 DEFLECTORS

Removal and Disassembly.............................................2-125
Assembly and Installation...............................................2-125

2.29 GRILLE:
XB9SX/XB12X/XB12XP/XB12SX

General...........................................................................2-126
Removal and Installation................................................2-126

2.30 FRONT MODULES: LIGHTNING AND
ULYSSES MODELS

Removal.........................................................................2-127
Installation......................................................................2-128

2.31 HANDLEBARS: FIREBOLT

General...........................................................................2-129
Removal.........................................................................2-129

Right Clip-On...........................................................2-129
Left Clip-On.............................................................2-129

Installation......................................................................2-129

Right Clip-On...........................................................2-129
Left Clip-On.............................................................2-129

2.32 HANDLEBARS: LIGHTNING AND
ULYSSES MODELS

Removal.........................................................................2-130
Installation......................................................................2-130

2.33 MIRRORS

Removal.........................................................................2-132
Installation......................................................................2-132

2.34 FOOTPEG, HEEL GUARD AND MOUNT:
FIREBOLT AND LIGHTNING MODELS

Rider...............................................................................2-133

REMOVAL...............................................................2-133
INSTALLATION........................................................2-133

Passenger......................................................................2-133

REMOVAL...............................................................2-133
INSTALLATION........................................................2-134

VI TABLE OF CONTENTS

TABLE OF CONTENTS

Summary of Contents for XB 2010










































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands

Buell XB 2010, Service Manual

Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands