manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

2.46

SIDESTAND

GENERAL

This motorcycle does NOT have a locking sidestand. Park
the motorcycle on a level, firm surface. An unbalanced
motorcycle can fall, which could result in death or serious
injury. (00122a)

The sidestand is located on the left side of the motorcycle. The
sidestand swings outward to support the motorcycle for parking.

REMOVAL

1.

Remove muffler. See 

4.19 EXHAUST SYSTEM, Removal

and Disassembly

.

2.

See 

Figure 2-203

 or 

Figure 2-203

. Remove fasteners (6)

securing sidestand bracket (5) to engine.

3.

Remove sidestand assembly.

DISASSEMBLY

TOOL NAME

PART NUMBER

SNAP-ON SPRING TOOL

HE-52B

NOTE

Sidestand assembly does not have to be removed from
motorcycle in order to remove sidestand leg.

1.

Remove two fasteners from the left side of chin fairing.
See 

2.50 CHIN FAIRING

.

2.

See 

Figure 2-202

 or 

Figure 2-203

. Remove sidestand leg.

3.

Retract sidestand leg (9).

4.

Remove sidestand spring (1) and spring extension plate
(3) using SNAP-ON SPRING TOOL (Part No. HE-52B).

5.

Remove sidestand pivot pin circlip (7) and remove
sidestand pivot pin (2).

6.

Extend sidestand leg (9) and remove.

sm00126

Figure 2-201. Sidestand (Retracted)

4

6

9

5

1

7

2

3

8

sm03932

1.

Sidestand spring

2.

Spring extension plate

3.

Pivot pin

4.

Spring post

5.

Sidestand bracket

6.

Sidestand bracket fasteners (2)

7.

Pivot pin circlip

8.

Tab, sidestand switch (HDI)

9.

Sidestand leg

Figure 2-202. Sidestand Assembly (Extended): Except

Ulysses Models

HOME

2010 XB Service: Chassis  2-159

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Maico MC 400 Service Bulletin preview
MC 400
Brand: Maico Pages: 13
Yamaha FJR1300AS Assembly Manual preview
FJR1300AS
Brand: Yamaha Pages: 94
Yamaha FJR1300(S) Supplementary Service Manual preview
FJR1300(S)
Brand: Yamaha Pages: 44
R&G CP0504BL Fitting Instructions Manual preview
CP0504BL
Brand: R&G Pages: 10
Sachs Bikes SAXY 25 Owner'S Manual preview
SAXY 25
Brand: Sachs Bikes Pages: 71
X-lite X-1002 Safety And Instructions For Use preview
X-1002
Brand: X-lite Pages: 76
DELTA PLUS Venitex BARRIER Technical Specs preview
Venitex BARRIER
Brand: DELTA PLUS Pages: 2
GAS GAS TXT BOY - 2006 User Manual preview
TXT BOY - 2006
Brand: GAS GAS Pages: 32
Fantic XX 125 Use And Maintenance Manual preview
XX 125
Brand: Fantic Pages: 153
BMW R 1200 R Classic Technical Data preview
R 1200 R Classic
Brand: BMW Pages: 1
Aosom 370-102 Assembly Instruction Manual preview
370-102
Brand: Aosom Pages: 13
Malaguti MADISON 125 Manual preview
MADISON 125
Brand: Malaguti Pages: 302
hepco & becker : 6519512 00 22-01-40 Manual preview
: 6519512 00 22-01-40
Brand: hepco & becker Pages: 9
KTM 1050 RR kit Installation Manual preview
1050 RR kit
Brand: KTM Pages: 10
KTM 350 SX-F 2017 Setup Instructions preview
350 SX-F 2017
Brand: KTM Pages: 22
Indian Motorcycle Scout 2015 Rider'S Manual preview
Scout 2015
Brand: Indian Motorcycle Pages: 122
ep PRN014567-014650 Installation Instructions Manual preview
PRN014567-014650
Brand: ep Pages: 21
GripOne IMU Quick Manual preview
IMU
Brand: GripOne Pages: 2

Brands by name

Popular brands

Load more brands