Buell XB 2010 Service Manual Download Page 14

Page: 14 / 714

Removal..................................................................2-175
Installation...............................................................2-175

Removal: Ulysses Models..............................................2-176
Installation: Ulysses Models...........................................2-176
Pillion Lock Removal: XB12R.........................................2-177
Pillion Lock Installation: XB12R......................................2-178

2.53 TRIPLE TAIL: ULYSSES MODELS

General...........................................................................2-179
Removal.........................................................................2-179
Disassembly...................................................................2-179
Assembly........................................................................2-179
Installation......................................................................2-180

2.54 LUGGAGE: XB12XT

Removal: Side Case.......................................................2-181
Installation: Side Case....................................................2-182
Removal: Top Case.........................................................2-182
Installation: Top Case.....................................................2-183
Luggage Case Latch Mechanism...................................2-183

Removal..................................................................2-183
Installation...............................................................2-184

2.55 LUGGAGE: XB12XP

Side Case.......................................................................2-185

Removal..................................................................2-185
Installation...............................................................2-186

Luggage Case Latch Mechanism...................................2-186

Removal..................................................................2-186
Installation...............................................................2-186

ENGINE

3.1 FASTENER TORQUE VALUES

Fastener Torque Values in this Chapter..............................3-1

3.2 SPECIFICATIONS

General...............................................................................3-3

3.3 ENGINE

Adjustment/Testing.............................................................3-7

General........................................................................3-7

Compression Test...............................................................3-7
Cylinder Leakage Test........................................................3-7
Diagnosing Smoking Engine or High Oil Consumption......3-8

3.4 ENGINE ROTATION FOR SERVICE

General...............................................................................3-9
Disassembly.......................................................................3-9
Assembly..........................................................................3-12

3.5 ENGINE REMOVAL

Disassembly.....................................................................3-14

3.6 ENGINE INSTALLATION

Assembly..........................................................................3-24

Engine Preparation for Re-installation.......................3-24
Installing Engine in Frame.........................................3-25

3.7 CYLINDER HEAD

Removal...........................................................................3-35

Rocker Box Assemblies.............................................3-35
Cylinder Head Assemblies........................................3-37

Disassembly.....................................................................3-37
Cleaning and Inspection...................................................3-40

Replacing Rocker Arm Bushings......................................3-42
Replacing Valve Guides....................................................3-43
Procedure For Using The Neway Valve Seat Cutter.........3-44
Assembly..........................................................................3-45
Push Rod Cover Installation.............................................3-46
Cylinder Head Installation.................................................3-47

3.8 CYLINDER AND PISTON

Removal/Disassembly......................................................3-51
Cleaning and Inspection...................................................3-52

Checking Gasket Surface..........................................3-53
Measuring Cylinder Bore...........................................3-53
Deglazing Cylinder....................................................3-54

Fitting Piston Rings..........................................................3-54
Connecting Rod Bushing..................................................3-56
Assembly/Installation........................................................3-57

3.9 OILING SYSTEM

General.............................................................................3-60

3.10 OIL PUMP

General.............................................................................3-61
Removal/Disassembly......................................................3-62
Cleaning and Inspection...................................................3-64
Assembly/Installation........................................................3-65

3.11 OIL RESERVOIR AND OIL HOSE
ROUTING

General.............................................................................3-67

3.12 OIL LINE FITTINGS

Removal...........................................................................3-69
Installation........................................................................3-69

3.13 OIL COOLER

General.............................................................................3-71
Removal...........................................................................3-71
Installation........................................................................3-71

3.14 OIL PRESSURE INDICATOR SWITCH

General.............................................................................3-72
Oil Pressure Signal Light..................................................3-72
Oil Pressure......................................................................3-72

3.15 CRANKCASE BREATHING SYSTEM

General.............................................................................3-74

VIII TABLE OF CONTENTS

TABLE OF CONTENTS

Summary of Contents for XB 2010










































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands

Buell XB 2010, Service Manual

Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands