manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

7.

Refer to 

Table 3-17

. Listen for air leaks at induction intake,

exhaust and head gasket.

NOTE

If air is escaping through valves, check push rod length.

8.

Repeat procedure on rear cylinder.

NOTE

After completing the compression test(s), make sure that the
throttle plate is in the closed position before starting engine.
Engine will start at an extremely high RPM if throttle plate is
left open.

Table 3-17. Air Leakage Test

POSSIBLE CAUSES

AIR LEAK LOCATION

Intake valve leaking.

Throttle body intake

Exhaust valve leaking.

Exhaust pipe

Leaking gasket.

Head gasket

DIAGNOSING SMOKING ENGINE OR HIGH
OIL CONSUMPTION

Perform the Compression Test. See 

3.3 ENGINE, Compression

Test

.

If further testing is needed, remove the suspect cylinder heads
and inspect the following:

•

Oil level

•

Valve guide seals

•

Valve guide-to-valve stem clearance

•

Gasket surface of both the cylinder head and the cylinder

•

Piston ring wear

HOME

3-8  2010 XB Service: Engine

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

DAELIM S3 Service Manual preview
S3
Brand: DAELIM Pages: 20
Yamaha XVS650A Owner'S Manual preview
XVS650A
Brand: Yamaha Pages: 86
Yamaha TW125 Parts Catalog preview
TW125
Brand: Yamaha Pages: 57
Yamaha TT-R90(R) Owner'S Service Manual preview
TT-R90(R)
Brand: Yamaha Pages: 288
Yamaha TRACER 700 2020 Owner'S Manual preview
TRACER 700 2020
Brand: Yamaha Pages: 98
Yamaha QT50 Service Manual preview
QT50
Brand: Yamaha Pages: 118
Yamaha XV1700PCR Road Star Warrior Owner'S Manual preview
XV1700PCR Road Star Warrior
Brand: Yamaha Pages: 122
Yamaha YZFR1W 2007 Service Manual preview
YZFR1W 2007
Brand: Yamaha Pages: 429
Yamaha XT225C Service Manual preview
XT225C
Brand: Yamaha Pages: 427
Yamaha Moto matrix YZF-R6S Supplementary Service Manual preview
Moto matrix YZF-R6S
Brand: Yamaha Pages: 41
KTM Power Parts 79612917000 Quick Start Manual preview
79612917000
Brand: KTM Power Parts Pages: 7
Ohlins HUSABERG MX 2000 Owner'S Manual preview
HUSABERG MX 2000
Brand: Ohlins Pages: 16
DUCATI Performance 96780761B Manual preview
96780761B
Brand: DUCATI Performance Pages: 9
Big Dog 2006 Chopper Owner'S Manual preview
2006 Chopper
Brand: Big Dog Pages: 100
Yamaha XJR1300(L) 99 Service Manual preview
XJR1300(L) 99
Brand: Yamaha Pages: 338
hepco & becker 630338 00 02 Mounting Instructions preview
630338 00 02
Brand: hepco & becker Pages: 4
DYNATEK DDK3-3 Installation Manual preview
DDK3-3
Brand: DYNATEK Pages: 12
Arai GP-6S Operation Instructions preview
GP-6S
Brand: Arai Pages: 2

Brands by name

Popular brands

Load more brands