manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

Trademarks

Buell. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-II
Referenced Products. . . . . . . . . . . . . . . . . . . . . . . . . . i-II

Transmission

Assembly, countershaft. . . . . . . . . . . . . . . . . . . . . . 5-38
Assembly, mainshaft. . . . . . . . . . . . . . . . . . . . . . . . . 5-38
Cleaning and Inspection, countershaft. . . . . . . . . . . 5-36
Cleaning and Inspection, mainshaft. . . . . . . . . . . . . 5-36
Disassembly, countershaft. . . . . . . . . . . . . . . . . . . . 5-36
Disassembly, mainshaft. . . . . . . . . . . . . . . . . . . . . . 5-35
Disassembly, mainshaft/countershaft. . . . . . . . . . . . 5-35
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
Installation, left crankcase. . . . . . . . . . . . . . . . . . . . 5-51
Installation, right crankcase. . . . . . . . . . . . . . . . . . . 5-53
Removal, left crankcase. . . . . . . . . . . . . . . . . . . . . . 5-31
Removal, right crankcase. . . . . . . . . . . . . . . . . . . . . 5-28

Transmission Case Bearings

Installation, left. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49
Installation, right. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-47

Transmission Fluid

Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

Transmission Left Case Bearings

Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49

Transmission Right Case Bearings

Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-47

Transmission Sprocket

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-58
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-57

Triple Tail

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-179
Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-179
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-179
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-180
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-179

Troubleshooting

Brake System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-30
Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53
Clutch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53
Electrical System. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53
Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-51
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-51
Lubrication System. . . . . . . . . . . . . . . . . . . . . . . . . . 1-52
Suspension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-54
Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53

Turn Signal Flasher

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-37
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-37

Turn Signals

Installation (Firebolt). . . . . . . . . . . . . . . . . . . . . . . . . 6-39
Installation (Firebolt). . . . . . . . . . . . . . . . . . . . . . . . . 6-42
Installation (Lightning). . . . . . . . . . . . . . . . . . . . . . . 6-39
Installation (Ulysses). . . . . . . . . . . . . . . . . . . . . . . . 6-40
Wire Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . 6-39

V

Valve Guides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

Cleaning and Inspection. . . . . . . . . . . . . . . . . . . . . . 3-41

Valves

Cleaning and Inspection. . . . . . . . . . . . . . . . . . . . . . 3-41

Valve Seats

Cleaning and Inspection. . . . . . . . . . . . . . . . . . . . . . 3-41

Valve Springs

Cleaning and Inspection. . . . . . . . . . . . . . . . . . . . . . 3-42

Valve Stem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44
Valve Stems

Valve Stem Clearances and Service Wear Limits
(table). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

Vehicle Identification Number. . . . . . . . . . . . . . . . . . . . . 2-19
Vehicle Speed Sensor

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-67
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-67

Voltage Regulator

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28

W

Wheel

Balancing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

Wheel Runout (table). . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Wheels

Bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
Bearings: Three Bearing Wheels. . . . . . . . . . . . . . . 2-38
Bearings: Two Bearing Wheels. . . . . . . . . . . . . . . . . 2-34
Cleaning and Inspection (Front). . . . . . . . . . . . . . . . 2-25
Cleaning and Inspection (Rear). . . . . . . . . . . . . . . . 2-31
Drive Sprocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Front Wheel Assembly. . . . . . . . . . . . . . . . . . . . . . . 2-26
Front Wheel Disassembly. . . . . . . . . . . . . . . . . . . . . 2-23
Front Wheel Installation. . . . . . . . . . . . . . . . . . . . . . 2-29
Front Wheel Removal. . . . . . . . . . . . . . . . . . . . . . . . 2-23
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Rear Wheel Disassembly. . . . . . . . . . . . . . . . . . . . . 2-32
Rear Wheel Installation. . . . . . . . . . . . . . . . . . . . . . 2-41
Rear Wheel Removal. . . . . . . . . . . . . . . . . . . . . . . . 2-31
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Valve Stem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44

Windscreen

Installation (Lightning). . . . . . . . . . . . . . . . . . . . . . 2-162
Installation (Ulysses/XB12XT). . . . . . . . . . . . . . . . 2-165
Installation (Ulysses). . . . . . . . . . . . . . . . . . . . . . . 2-163
Removal (Lightning). . . . . . . . . . . . . . . . . . . . . . . . 2-162
Removal (Ulysses). . . . . . . . . . . . . . . . . . . . . . . . . 2-163
Removal (Ulysses). . . . . . . . . . . . . . . . . . . . . . . . . 2-164

Windshield

Installation (Firebolt). . . . . . . . . . . . . . . . . . . . . . . . 2-161
Installation (Ulysses/XB12XT). . . . . . . . . . . . . . . . 2-165
Installation (Ulysses). . . . . . . . . . . . . . . . . . . . . . . 2-163
Removal (Firebolt). . . . . . . . . . . . . . . . . . . . . . . . . 2-161
Removal (Ulysses). . . . . . . . . . . . . . . . . . . . . . . . . 2-163
Removal (Ulysses). . . . . . . . . . . . . . . . . . . . . . . . . 2-164

Windshield Maintenance

General (Firebolt). . . . . . . . . . . . . . . . . . . . . . . . . . . 1-49

Winter Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Wiring Diagram Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . B-4

XXXIV  INDEX

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

hepco & becker 501546 00 01 Manual preview
501546 00 01
Brand: hepco & becker Pages: 5
Abisal Nils Extreme MTW03 User Manual preview
Nils Extreme MTW03
Brand: Abisal Pages: 21
Metra Electronics Saddle Tramp BC-BTHBSP Installation Instructions Manual preview
Saddle Tramp BC-BTHBSP
Brand: Metra Electronics Pages: 8
R&G CP0485 Fitting Instructions Manual preview
CP0485
Brand: R&G Pages: 47
KTM Freeride 350 AUS Setup Instructions preview
Freeride 350 AUS
Brand: KTM Pages: 25
Suzuki LT-A400FK3 Setup Manual preview
LT-A400FK3
Brand: Suzuki Pages: 42
MOTO GUZZI V7 CLASSIC Service Manual preview
V7 CLASSIC
Brand: MOTO GUZZI Pages: 134
R&G RSET02BK Fitting Instructions Manual preview
RSET02BK
Brand: R&G Pages: 17
R&G LP0347 Fitting Instructions Manual preview
LP0347
Brand: R&G Pages: 18
R&G LP0253BK Fitting Instructions Manual preview
LP0253BK
Brand: R&G Pages: 17
Yamaha YZF-R1 Assembly Instructions Manual preview
YZF-R1
Brand: Yamaha Pages: 15
Yamaha YW50A Owner'S Manual preview
YW50A
Brand: Yamaha Pages: 84
Dynafit RADICAL 2.0 User Manual preview
RADICAL 2.0
Brand: Dynafit Pages: 21
MARLINK SmallTrack Assembly Instructions preview
SmallTrack
Brand: MARLINK Pages: 3
Aosom 370-102 Assembly Instruction Manual preview
370-102
Brand: Aosom Pages: 13
Malaguti CIAK MASTER 50-4T Electric System Troubleshooting preview
CIAK MASTER 50-4T
Brand: Malaguti Pages: 31
Tanox WeldGuard ADF-206S User Manual preview
WeldGuard ADF-206S
Brand: Tanox Pages: 16
Yamaha 100LS2 Service Manual preview
100LS2
Brand: Yamaha Pages: 98

Brands by name

Popular brands

Load more brands