Buell XB 2010 Service Manual Download Page 13

Page: 13 / 714

2.35 HEEL GUARD AND FOOTPEG
MOUNTS: ULYSSES MODELS

Rider Footpegs...............................................................2-135

Footpeg Removal....................................................2-135
Footpeg Installation.................................................2-135

Passenger Footpegs.......................................................2-135

Footpeg Removal....................................................2-135
Footpeg Installation.................................................2-135

Mount Removal..............................................................2-135
Mount Installation...........................................................2-135
Heel Guard Replacement...............................................2-136

2.36 SPROCKET COVER

Removal.........................................................................2-137
Installation......................................................................2-137

2.37 BELT GUARDS

Removal.........................................................................2-138
Installation......................................................................2-138

2.38 INTAKE COVER

Removal.........................................................................2-139
Installation......................................................................2-139

2.39 SUBFRAME TAIL ASSEMBLY AND
BODY WORK: FIREBOLT

Disassembly...................................................................2-141
Cleaning.........................................................................2-144
Assembly........................................................................2-144

2.40 LEFT TAIL SECTION AND BATTERY
PAN: LIGHTNING MODELS

Disassembly...................................................................2-146
Cleaning.........................................................................2-147
Assembly........................................................................2-148

2.41 CENTER TAIL SECTION: LIGHTNING
MODELS

Disassembly...................................................................2-150
Assembly........................................................................2-150

2.42 RIGHT TAIL SECTION: LIGHTNING
MODELS

Disassembly...................................................................2-151
Assembly........................................................................2-151

2.43 LEFT AND RIGHT TAIL SECTION:
ULYSSES MODELS

Disassembly/Left and/or Right Side Tail Section............2-152
Cleaning.........................................................................2-154
Assembly........................................................................2-154

2.44 CENTER TAIL LOOP: ULYSSES
MODELS

Disassembly...................................................................2-156
Assembly........................................................................2-156

2.45 TRUNK AND BATTERY PAN: ULYSSES
MODELS

Disassembly Trunk and Battery Pan...............................2-158
Assembly/Trunk Pan and Battery Pan............................2-158

2.46 SIDESTAND

General...........................................................................2-159
Removal.........................................................................2-159
Disassembly...................................................................2-159
Assembly........................................................................2-160
Installation......................................................................2-160

2.47 FRONT FAIRING, WINDSHIELD, AND
MIRRORS: FIREBOLT

Removal.........................................................................2-161
Installation......................................................................2-161

2.48 WINDSHIELD AND WINDSCREEN:
LIGHTNING AND ULYSSES MODELS

Lightning.........................................................................2-162

Removal..................................................................2-162
Installation...............................................................2-162

Ulysses XB12X...............................................................2-163

Removal..................................................................2-163
Installation...............................................................2-163

Ulysses XB12XT/XB12XP..............................................2-164

Removal..................................................................2-164
Installation...............................................................2-165

2.49 AIR SCOOPS

Ram Air Scoop...............................................................2-166

Removal..................................................................2-166
Installation...............................................................2-166

Engine Shroud Air Scoop...............................................2-166

Removal..................................................................2-166
Installation...............................................................2-166

Oil Cooler Air Scoop.......................................................2-166

Removal..................................................................2-166
Installation...............................................................2-166

Ram Air Scoop and Fan Shroud: Ulysses......................2-168

Removal..................................................................2-168
Installation...............................................................2-168

2.50 CHIN FAIRING

Removal.........................................................................2-170
Installation......................................................................2-170

2.51 SEAT

Firebolt...........................................................................2-171

Rider Seat...............................................................2-171
Pillion.......................................................................2-171

Lightning.........................................................................2-171

Removal..................................................................2-171
Installation...............................................................2-172

Ulysses...........................................................................2-173

Removal..................................................................2-173
Installation...............................................................2-173

2.52 SEAT LOCKS

Lightning.........................................................................2-175

TABLE OF CONTENTS VII

TABLE OF CONTENTS

Summary of Contents for XB 2010










































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands

Buell XB 2010, Service Manual

Search results

Summary of Contents for XB 2010

Reviews:

Related manuals for XB 2010

Brands by name

Popular brands