Buell XB 2010 Service Manual Download Page 240 | Manualshive

Page: 240 / 714

background image

5

4

3

2

1

9

8

7

6

sm05260

1.

Sidestand spring

2.

Spring extension plate

3.

Pivot pin

4.

Spring post

5.

Sidestand bracket

6.

Sidestand bracket fasteners (3)

7.

Pivot pin circlip

8.

Tab, sidestand switch (HDI)

9.

Sidestand leg

Figure 2-203. Sidestand Assembly: Ulysses Models

ASSEMBLY

TOOL NAME

PART NUMBER

SNAP-ON SPRING TOOL

HE-52B

1.

. Install sidestand leg (9).

2.

Lubricate sidestand pivot pin and mating portions on
sidestand bracket with WHEEL BEARING GREASE (Part
No. 99855-89) as shown in

3.

See

. Install sidestand leg (9) to bracket (5)

by installing the pivot pin (3) and pivot pin circlip (7).

4.

Retract sidestand leg (9).

5.

Install spring extension plate (2) and sidestand spring (1)
using SNAP-ON SPRING TOOL (Part No. HE-52B).

6.

Extension plate should curve away from primary chain
adjustment screw to allow for clearance around adjustment
screw.

INSTALLATION

1.

. Apply LOCTITE 271 (red) to the

sidestand bracket fasteners (6). Loosely install the
sidestand assembly to the crankcase with the sidestand
bracket fasteners (6). Extend the sidestand leg (9) and
hold forward in the fully extended position while tightening
the sidestand bracket fasteners in the following sequence:

a.

Tighten the front fastener(s) to 25-27 ft-lbs (33.9-36.6
Nm).

b.

Tighten the rear fastener to 25-27 ft-lbs (33.9-36.6
Nm).

2.

Repeat the tightening sequence in the previous step to
verify proper clamp load.

3.

Install muffler. See

4.19 EXHAUST SYSTEM, Assembly

and Installation

4.

Install chin fairing fasteners. See

2.50 CHIN FAIRING

.

5.

Extend and retract sidestand leg to check for proper
operation.

sm00129

Figure 2-204. Sidestand Assembly Lubrication (Shaded

Areas) (Typical)

2-160 2010 XB Service: Chassis

«
...
238
239
240
241
242
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: BMW Pages: 245

Nils Extreme MTW03

Brand: Abisal Pages: 21

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: hepco & becker Pages: 4

Brand: yasuni Pages: 12

Brand: kellermann Pages: 7

Brand: Shift Power Pages: 7

Brand: Baotian Pages: 22

Brand: RIEJU Pages: 116

Brand: Petzl Pages: 12

Brand: KTM Pages: 12

Brand: Honda Pages: 177

Brand: Honda Pages: 112

Brand: YEC Pages: 62

Brand: Dakota Digital Pages: 4

Brand: um Pages: 48

Brand: Ohlins Pages: 4

Brand: GAS GAS Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands