manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

INSTALLATION

1.

See 

Figure 6-88

 (Firebolt), 

Figure 6-89

 (Lightning) or

Figure 6-90

 (Ulysses). Place instrument module (2) into

position in support (1).

2.

Install washers (4) and fasteners (5). Tighten fasteners to
12-36 in-lbs (1.4-4 Nm).

3.

See 

Figure 6-85

 (Firebolt), 

Figure 6-86

 (Lightning), or

Figure 6-87

 (Ulysses). Connect instrument module con-

nector [39].

4.

For Firebolt, install headlight support bracket and install
front fairing. See 

2.26 HEADLAMP ASSEMBLY AND

SUPPORT BRACKET

.

5.

For Lightning, install windscreen and for Ulysses, install
windscreen/windshield. See 

2.26 HEADLAMP ASSEMBLY

AND SUPPORT BRACKET

.

6.

Install negative battery cable.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

7.

Install seat.

sm00414

Figure 6-85. Instrument Module Connector [39]: Firebolt

sm00466a

Figure 6-86. Instrument Module Connector [39]: Lightning

sm00465a

Figure 6-87. Instrument Module Connector [39]: Ulysses

HOME

2010 XB Service: Electrical  6-69

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

GAS GAS TXT PRO - 2007 Parts List preview
TXT PRO - 2007
Brand: GAS GAS Pages: 70
LAMAX eJumper DB50 User Manual preview
eJumper DB50
Brand: LAMAX Pages: 134
Parweld XR936H Instruction Manual preview
XR936H
Brand: Parweld Pages: 4
MV Agusta F4 750 Instructions Manual preview
F4 750
Brand: MV Agusta Pages: 36
Honda 08L42-MCA-100 Installation Instructions preview
08L42-MCA-100
Brand: Honda Pages: 3
KTM Power Parts 77202923000 Information preview
77202923000
Brand: KTM Power Parts Pages: 7
HYOSUNG GT650SR - PARTS CATALOGUE Parts Catalog preview
GT650SR - PARTS CATALOGUE
Brand: HYOSUNG Pages: 124
DELTA PLUS Venitex BARRIER Technical Specs preview
Venitex BARRIER
Brand: DELTA PLUS Pages: 2
X-lite X-902 Directions For Use Manual preview
X-902
Brand: X-lite Pages: 84
Free Spirits 308927 Instructions Manual preview
308927
Brand: Free Spirits Pages: 28
Yamaha Star XV250Y Owner'S Manual preview
Star XV250Y
Brand: Yamaha Pages: 94
Yamaha Star XVS13CG 2015 Owner'S Manual preview
Star XVS13CG 2015
Brand: Yamaha Pages: 98
Yamaha Star XV250G 2015 Owner'S Manual preview
Star XV250G 2015
Brand: Yamaha Pages: 88
Yamaha Star XVS13CTD 2012 Owner'S Manual preview
Star XVS13CTD 2012
Brand: Yamaha Pages: 104
Yamaha Star XVS11X Owner'S Manual preview
Star XVS11X
Brand: Yamaha Pages: 104
Yamaha Star XV250H 2016 Owner'S Manual preview
Star XV250H 2016
Brand: Yamaha Pages: 98
Yamaha Star XVS95B Owner'S Manual preview
Star XVS95B
Brand: Yamaha Pages: 98
IBEX ZIEGER 10005243 Mounting Instructions preview
ZIEGER 10005243
Brand: IBEX Pages: 4

Brands by name

Popular brands

Load more brands