manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

ADJUSTMENT

TOOL NAME

PART NUMBER

WHEEL TRUING AND BALANCING
STAND

HD-99500-80

Wheel Balancing

Wheel balancing is recommended to improve handling and
reduce vibration, especially at high road speeds.

In most cases, static balancing using WHEEL TRUING AND
BALANCING STAND (Part No. HD-99500-80) will produce
satisfactory results. However, dynamic balancing, utilizing a
wheel spinner, can be used to produce finer tolerances for
better high-speed handling characteristics. Follow the instruc-
tions supplied with the balance machine you are using.

Wheels should be balanced to within 1/4 oz. (7 g) at 60 MPH
(97 KM/H).

See 

Figure 2-53

. Use only genuine WHEEL WEIGHTS (Part

No. G0312.7AA) which have special self-adhesive backings.
Apply WHEEL WEIGHTS to the flat surface of the wheel rim.

Refer to 

Table 2-23

 for maximum weight permissible to

accomplish balance.

1.

Make sure that area of application is completely clean,
dry and free of oil and grease.

2.

Remove paper backing from weight. For additional
adhesive strength, apply three drops of LOCTITE
SUPERBONDER 420 to adhesive side of weight.

3.

On the front wheel, locate a flat surface on the right side
of the wheel rim. On the rear wheel locate a flat surface.
Press weight firmly in place, holding for ten seconds.

4.

Allow eight hours for adhesive to cure completely before
using wheel.

NOTE

If wheel assembly is out of specification (1 oz. front, 2 oz. rear)
rotate tire on rim and rebalance until wheel is within specifica-
tion.

Table 2-23. Maximum Weight Applied To Cast Wheels

MAXIMUM WEIGHT

WHEEL

1.0 oz. (28 g)

Front

2.0 oz. (56 g)

Rear

sm06686

Figure 2-53. Wheel Weights

HOME

2010 XB Service: Chassis  2-47

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

KEDO 31118MR Quick Start Manual preview
31118MR
Brand: KEDO Pages: 2
KEDO 60520R Manual preview
60520R
Brand: KEDO Pages: 3
KEDO 31103 Manual preview
31103
Brand: KEDO Pages: 2
Cobra 602-3000 Instruction Manual preview
602-3000
Brand: Cobra Pages: 2
Honda CB-1 89 Service Manual preview
CB-1 89
Brand: Honda Pages: 178
Suzuki DL1000AL4 Owner'S Manual preview
DL1000AL4
Brand: Suzuki Pages: 26
Yamaha GRIZZLY 90 2020 Owner'S Manual preview
GRIZZLY 90 2020
Brand: Yamaha Pages: 132
Yamaha RAPTOR 90 2020 Owner'S Manual preview
RAPTOR 90 2020
Brand: Yamaha Pages: 132
Yamaha YFM45FGZ Owner'S Manual preview
YFM45FGZ
Brand: Yamaha Pages: 166
Yamaha XVZ12L Service Manual preview
XVZ12L
Brand: Yamaha Pages: 452
Yamaha YFM09GYXM 2020 Owner'S Manual preview
YFM09GYXM 2020
Brand: Yamaha Pages: 132
DYNATEK DDK1-11 Installation Manual preview
DDK1-11
Brand: DYNATEK Pages: 11
IBEX X-Line Mounting Instruction preview
X-Line
Brand: IBEX Pages: 3
Triumph ACCESORIES 2005 Price List preview
ACCESORIES 2005
Brand: Triumph Pages: 6
Triumph Clothing Range 2006 Catalog preview
Clothing Range 2006
Brand: Triumph Pages: 19
Triumph 2007 ROCKET III Overview preview
2007 ROCKET III
Brand: Triumph Pages: 20
Triumph Speed Triple Handbook preview
Speed Triple
Brand: Triumph Pages: 136
Triumph Speed Triple 1200 RS Owner'S Handbook Manual preview
Speed Triple 1200 RS
Brand: Triumph Pages: 184

Brands by name

Popular brands

Load more brands