manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

6.28

INTERACTIVE EXHAUST HARNESS: XB12
MODELS

FIREBOLT

Removal

1.

Remove seat and pillion.

2.

Remove intake cover assembly. See 

2.38 INTAKE

COVER

.

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

3.

Remove negative battery cable from battery.

4.

Remove main battery ground.

5.

Remove the subframe tail body work. See 

2.39 SUB-

FRAME TAIL ASSEMBLY AND BODY WORK: FIREBOLT

.

6.

See 

Figure 6-109

. Separate exhaust actuator harness

connector [165] (5) at main harness.

7.

Note location of cable strap and cut as required.

8.

Pull actuator harness through frame.

9.

Disconnect connector [161B] from actuator.

NOTE

For actuator and actuator cable replacement see

6.16 INTERACTIVE EXHAUST SYSTEM

.

2

3

1

4

sm00432

1.

Fuel vent hose

2.

Main wire harness

3.

Cable strap

4.

Rear shock reservoir hose

Figure 6-109. Left Side Subframe Hose and Wire Routing:

Firebolt

1

2

3

sm00433

1.

Main battery ground

2.

Wire harness ground

3.

Main fuse case

Figure 6-110. Battery and Harness Ground (Battery

Removed for Clarity)

Installation

1.

Mate actuator connector [161B] to actuator.

2.

Route harness along channel in air cleaner under frame
and under main wiring harness.

NOTE

If cable is routed in front of the frame lug it will cause the muffler
valve to stay open not allowing it to work properly.

3.

See 

Figure 6-111

. Verify that the interactive exhaust wiring

harness (2) is routed behind the frame lug (1) before
installing air intake cover.

4.

Mate exhaust actuator harness connector halves [165].

5.

Install cable straps where noted.

6.

Install ground bolt through main battery ground cable.
Tighten to 48-72 in-lbs (5.4-8 Nm).

7.

Connect negative battery cable to battery terminal. Tighten
fastener to 60-70 in-lbs (6.8-7.9 Nm).

8.

Install subframe tail body work. See 

2.39 SUBFRAME

TAIL ASSEMBLY AND BODY WORK: FIREBOLT

.

9.

Install intake cover. Tighten fasteners to 12-36 in-lbs (1.4-
4 Nm). See 

2.38 INTAKE COVER

.

HOME

6-90  2010 XB Service: Electrical

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Free Spirits 088305 Instructions Manual preview
088305
Brand: Free Spirits Pages: 32
KEDO 31118MR Quick Start Manual preview
31118MR
Brand: KEDO Pages: 2
KEDO 60520R Manual preview
60520R
Brand: KEDO Pages: 3
KEDO 31103 Manual preview
31103
Brand: KEDO Pages: 2
Christopeit Sport MB2 9840A Assembly And Exercise Instructions preview
MB2 9840A
Brand: Christopeit Sport Pages: 16
Biltema 82-720 User Manual preview
82-720
Brand: Biltema Pages: 2
HERO ACHIEVER 150 Manual preview
ACHIEVER 150
Brand: HERO Pages: 68
Ducati SUPERSPORT1000 2003 Owner'S Manual preview
SUPERSPORT1000 2003
Brand: Ducati Pages: 328
Denali LAH.07.10401 Instruction Manual preview
LAH.07.10401
Brand: Denali Pages: 2
Honda XRM125 CFT125 2020 Owner'S Manual preview
XRM125 CFT125 2020
Brand: Honda Pages: 111
BMW S 1000XR 2018 Rider'S Manual preview
S 1000XR 2018
Brand: BMW Pages: 241
Triumph 1050 Sprint Owner'S Handbook Manual preview
1050 Sprint
Brand: Triumph Pages: 126
Arai Helmet RAM-X Operation Instructions Manual preview
RAM-X
Brand: Arai Helmet Pages: 20
Saddlemen RIGID SADDLEBAG Installation Instructions preview
RIGID SADDLEBAG
Brand: Saddlemen Pages: 2
BOS Suspension Factory Series Service Manual preview
Factory Series
Brand: BOS Suspension Pages: 32
yasuni CROSS Assembly Instructions Manual preview
CROSS
Brand: yasuni Pages: 12
Benelli BN600GT Owner'S Manual preview
BN600GT
Brand: Benelli Pages: 314
Beta RR 350 EFI Operating Instructions Manual preview
RR 350 EFI
Brand: Beta Pages: 82

Brands by name

Popular brands

Load more brands