manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

ASSEMBLY

TOOL NAME

PART NUMBER

FRONT WHEEL BEARING INSTALLER

B-43993-10

BACKING PLATE

B-43993-11 FRONT
WHEEL

WHEEL BEARING
REMOVER/INSTALLER KIT

B-43993-50A

FRONT WHEEL BEARING REMOVER
COLLET

B-43993-7

FRONT BEARING INSTALLER

B-43993-9

FRONT BEARING INSTALLER

B-43993-9, FROM
KIT PART NO. B-
43993-50A

WHEEL BEARING
INSTALLER/REMOVER

HD-44060A

EXTREME PRESSURE LUBRICANT

J-23444-A

See 

Figure 2-16

. Install new wheel bearings (2) into hub using

suitable driver. Press on outer race only.

NOTES

•

Press the rotor side bearing in first ensuring it is seated
on the shoulder of the wheel. Followed by pressing the
alternate side until it contacts the spacer.

•

The WHEEL BEARING REMOVER/INSTALLER KIT (Part
No. B-43993-50A) consists of the FRONT WHEEL
BEARING REMOVER COLLET (Part No. B-43993-7),
FRONT WHEEL BEARING INSTALLER (Part No. B-
43993-10) and BACKING PLATE (Part No. B-43993-11
front wheel).

Be sure that brake fluid or other lubricants do not contact
brake pads or discs. Such contact can adversely affect
braking ability, which could cause loss of control, resulting
in death or serious injury. (00290a)

Bearing Installation

NOTE

Always install the brake side bearing first with the lettering
facing out from the hub.

The procedure describes the bearing installation for the front
wheel; the procedure will be the same for two bearing rear
wheels.

1

2

sm00518

1.

Backing plate

2.

Forcing screw

Figure 2-11. Install the Backing Plate (B-43993-12) and

Forcing Screw

1.

See 

Figure 2-11

. Install the BACKING PLATE (Part No. B-

43993-11 front wheel) (1) onto the long forcing screw (2)
from the WHEEL BEARING INSTALLER/REMOVER (Part
No. HD-44060A), with the smaller diameter toward the
wheel hub. Insert the forcing screw and backing plate into
the wheel hub.

2.

See 

Figure 2-12

. Sparingly apply EXTREME PRESSURE

LUBRICANT (Part No. J-23444-A) to the threads of the
long forcing screw (1) to prolong service life and verify
smooth operation.

HOME

2-26  2010 XB Service: Chassis

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

ZERO GRAVITY SR Series Installation Manual preview
SR Series
Brand: ZERO GRAVITY Pages: 6
GAS GAS EC450 2009 User Manual preview
EC450 2009
Brand: GAS GAS Pages: 69
Eastwood 21195 Instructions Manual preview
21195
Brand: Eastwood Pages: 8
GPX Demon 150GR Introduction Manual preview
Demon 150GR
Brand: GPX Pages: 44
Shark RSJ User Manual preview
RSJ
Brand: Shark Pages: 44
SP CONNECT BAR CLAMP MOUNT PRO Mounting Instructions preview
BAR CLAMP MOUNT PRO
Brand: SP CONNECT Pages: 3
hepco & becker 5054558 00 01 Manual preview
5054558 00 01
Brand: hepco & becker Pages: 4
Race Dynamics PowerTRONIC Installation Manual preview
PowerTRONIC
Brand: Race Dynamics Pages: 25
Vance and hines Competition Series Quick Start Manual preview
Competition Series
Brand: Vance and hines Pages: 2
Vance and hines 48425 Installation Instructions preview
48425
Brand: Vance and hines Pages: 5
Vance and hines 48241 Installation Instructions preview
48241
Brand: Vance and hines Pages: 4
R&G FI0088BK Fitting Instructions preview
FI0088BK
Brand: R&G Pages: 2
Starke TR-2503 Operation Manual preview
TR-2503
Brand: Starke Pages: 20
Fuelpak SOFTAIL 2012 Instructions preview
SOFTAIL 2012
Brand: Fuelpak Pages: 2
Yamaha TN359 Quick Start Manual preview
TN359
Brand: Yamaha Pages: 4
Yamaha FZR 600 Service Manual preview
FZR 600
Brand: Yamaha Pages: 12
Yamaha FZR600R Service Manual preview
FZR600R
Brand: Yamaha Pages: 40
Yamaha FZR600RB Supplementary Service Manual preview
FZR600RB
Brand: Yamaha Pages: 53

Brands by name

Popular brands

Load more brands