manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

INSTALLATION

NOTES

•

Do not install sensors that have been dropped or impacted
by other components. Damage to the sensing element
may have occurred. Replacement sensor assemblies have
threads coated with anti-seize lubricant and new seal rings.

•

If reinstalling O2 sensor, apply a thin coat of anti-seize
(Part No. 98960-97) to threads of each O2 sensor prior to
installing in header. Do not use any other grease or sealant
product on sensor threads. The electrical connector must
also be clean and free of any dielectric grease.

1.

Apply LOCTITE ANTI-SEIZE LUBRICANT to threads of
rear sensor.

a.

See 

Figure 4-16

. Thread sensor into rear exhaust

header. Tighten sensor to 40-45 ft-lbs (54.2-61 Nm).

b.

Install cooling fan. See 

4.11 COOLING FAN

.

c.

Install shock absorber. See 

2.23 REAR SHOCK

ABSORBER

.

d.

See 

Figure 4-17

. Connect 1-place connector [137] to

wiring harness.

e.

Install sensor lead into retainer.

f.

Install air cleaner assembly. See 

4.3 AIR CLEANER

ASSEMBLY

.

g.

Install intake cover assembly. See 

2.38 INTAKE

COVER

.

2.

Apply LOCTITE ANTI-SEIZE LUBRICANT to threads of
front sensor.

a.

See 

Figure 4-16

. Thread sensor into front exhaust

header. Tighten sensor to 40-45 ft-lbs (54.2-61 Nm).

b.

See 

Figure 4-17

. Connect 1-place connector [137] to

wiring harness.

c.

Install sensor lead into retainer.

d.

Install retainer to the inside of the inner engine shroud
air scoop.

e.

Install fasteners securing the inner engine shroud air
scoop to the fuel tank/frame and tighten to 12-36 in-
lbs (1.4-4 Nm).

f.

Install fasteners securing the outer engine shroud air
scoop to the inner ram air scoop and tighten to 21.6-
26.4 in-lbs (2.4-3 Nm).

Do not over-tighten bolts on battery terminals. Use
recommended torque values. Over-tightening battery ter-
minal bolts could result in damage to battery terminals.
(00216a)

3.

Connect negative battery cable.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

4.

Install seat.

sm00231

Figure 4-16. Rear Oxygen Sensor (Shock Absorber

Removed)

HOME

2010 XB Service: Fuel System  4-13

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Cannondale MX400 Parts Catalog preview
MX400
Brand: Cannondale Pages: 61
ZARD ZUMA Fitting Manual preview
ZUMA
Brand: ZARD Pages: 2
hepco & becker 410999 00 01 Quick Start Manual preview
410999 00 01
Brand: hepco & becker Pages: 2
KTM F3001P2 2016 Setup Instructions preview
F3001P2 2016
Brand: KTM Pages: 29
Zero Motorcycles Zero S Series 2014 Owner'S Manual preview
Zero S Series 2014
Brand: Zero Motorcycles Pages: 128
Honda st1300/a 2007 Setup Instructions preview
st1300/a 2007
Brand: Honda Pages: 28
Honda CBF600N 2006 Owner'S Manual preview
CBF600N 2006
Brand: Honda Pages: 150
KTM 690 Enduro R 2019 Owner'S Manual preview
690 Enduro R 2019
Brand: KTM Pages: 274
Zontes ZT310-X Service Manual preview
ZT310-X
Brand: Zontes Pages: 119
thousand TRAVELER LIGHT Owner'S Manual preview
TRAVELER LIGHT
Brand: thousand Pages: 32
DELTA PLUS Venitex BARRIER Technical Specs preview
Venitex BARRIER
Brand: DELTA PLUS Pages: 2
Dennis Kirk Firstgear 512817 Manual preview
Firstgear 512817
Brand: Dennis Kirk Pages: 2
Isotta SP8106 R1200R Fitting Instructions preview
SP8106 R1200R
Brand: Isotta Pages: 2
Ecomobility Green World LIPO45 User Manual preview
LIPO45
Brand: Ecomobility Green World Pages: 24
DYNATEK D3K3-1 Installation Instructions preview
D3K3-1
Brand: DYNATEK Pages: 4
DYNATEK D3K2-2 Installation Instructions preview
D3K2-2
Brand: DYNATEK Pages: 4
DYNATEK D2K-HD2 User Instructions preview
D2K-HD2
Brand: DYNATEK Pages: 5
TVS TVS XL 100 Manual preview
TVS XL 100
Brand: TVS Pages: 44

Brands by name

Popular brands

Load more brands