manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

4.11

COOLING FAN

GENERAL

A computer-controlled cooling fan assists engine cooling during
operation in high temperatures. Fan actuation is controlled by
engine temperature and vehicle speed.

REMOVAL

1.

Remove seat.

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

2.

Disconnect negative battery cable.

NOTE

XB12X/XB12XT/XB12P: Remove the fan shroud. See 

2.49 AIR

SCOOPS, Ram Air Scoop and Fan Shroud: Ulysses

.

3.

Remove shock absorber. See 

2.23 REAR SHOCK

ABSORBER

.

4.

See 

Figure 4-27

. Remove cooling fan fasteners (1).

5.

Rotated fan clockwise (looking towards front of vehicle)
to remove.

6.

See 

Figure 4-28

. Disconnect cooling fan connector [97].

INSTALLATION

1.

See 

Figure 4-28

. Connect cooling fan connector [97].

NOTES

•

See 

Figure 4-27

. When installing cooling fan (3), be sure

wiring, transmission vent hose and fuel line are routed
through notch (2) in fan body.

•

On California models, both fuel tank and canister vent
hoses are routed through notch in fan body.

2.

Install cooling fan and rotate counterclockwise into posi-
tion.

3.

Install cooling fan fasteners. Tighten to 12-36 in-lbs (1.4-
4 Nm).

4.

Install shock absorber. See 

2.23 REAR SHOCK

ABSORBER

.

NOTE

XB12X/XB12XT/XB12P: Install the fan shroud. See 

2.49 AIR

SCOOPS, Ram Air Scoop and Fan Shroud: Ulysses

.

5.

Connect negative battery cable, tightening to 60-70 in-lbs
(6.8-7.9 Nm).

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

6.

Install seat.

1

3

2

sm00247

1.

Cooling fan fasteners

2.

Notch

3.

Cooling fan

Figure 4-27. Cooling Fan

sm00248

Figure 4-28. Cooling Fan Connector [97]

HOME

2010 XB Service: Fuel System  4-21

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Baja motorsports BV250 Setup Instructions preview
BV250
Brand: Baja motorsports Pages: 8
Yukon Trail Badger 100 Owner'S Manual preview
Badger 100
Brand: Yukon Trail Pages: 24
Dakota Digital VHX systems Operating Manual preview
VHX systems
Brand: Dakota Digital Pages: 6
National Cycle Spartan N21202 Installation Instructions preview
Spartan N21202
Brand: National Cycle Pages: 3
Braaap CRUISER400 User Manual preview
CRUISER400
Brand: Braaap Pages: 40
Memphis Shades MEM-9917 Quick Start Manual preview
MEM-9917
Brand: Memphis Shades Pages: 2
KTM Freeride 350 AUS Setup Instructions preview
Freeride 350 AUS
Brand: KTM Pages: 25
AGV AX-8 Dual Owner'S Instructions Manual preview
AX-8 Dual
Brand: AGV Pages: 64
LAZER Mambo Evo PURE CARBON User Manual preview
Mambo Evo PURE CARBON
Brand: LAZER Pages: 13
Spartus 901X User Manual preview
901X
Brand: Spartus Pages: 24
SRC KTM390-14-01-SL Quick Start Manual preview
KTM390-14-01-SL
Brand: SRC Pages: 4
X-lite X-1003 Safety And Instructions For Use preview
X-1003
Brand: X-lite Pages: 100
Yamaha FZ-07 2016 Owner'S Manual preview
FZ-07 2016
Brand: Yamaha Pages: 112
Surtek CSS01 User Manual And Warranty preview
CSS01
Brand: Surtek Pages: 12
R&G FI0094BK Fitting Instructions preview
FI0094BK
Brand: R&G Pages: 4
R&G FI0062BK Fitting Instructions preview
FI0062BK
Brand: R&G Pages: 2
R&G FI0114BK Fitting Instructions Manual preview
FI0114BK
Brand: R&G Pages: 6
R&G FI0075BK Fitting Instructions preview
FI0075BK
Brand: R&G Pages: 4

Brands by name

Popular brands

Load more brands