Buell XB 2010 Service Manual Download Page 248 | Manualshive

Page: 248 / 714

background image

RAM AIR SCOOP AND FAN SHROUD:
ULYSSES

Removal

1.

. Remove fasteners securing the outer

ram air scoop to the inner ram air scoop.

NOTE

After removing fasteners securing the inner ram air scoop to
the fuel tank/frame, it will be necessary to detach the Oxygen
Sensor connector from the inside of the scoop.

2.

Remove fasteners securing the inner ram air scoop to the
fuel tank/frame.

3.

Remove front oxygen sensor connector. See

4.

Remove seat.

NOTE

Remove saddlebags and brackets if required. See

.

Disconnect negative (-) battery cable first. If positive (+)
cable should contact ground with negative (-) cable con-
nected, the resulting sparks can cause a battery explosion,
which could result in death or serious injury. (00049a)

5.

See

6.26 MAIN WIRE HARNESS

. Disconnect battery

cables from battery: negative cable (7) (black) first.

6.

Remove battery.

7.

Disconnect ECM connectors [10] and [11].

8.

Remove battery pan.

a.

Remove ECM (3). See

4.7 OXYGEN SENSORS (O2)

b.

Disconnect rear brake light switch connector [121].

c.

Remove fuse block and relay center (4).

d.

Remove main harness and plastic grommet (6) from
battery pan.

e.

Remove fasteners securing battery pan to left and
right tail section.

f.

Lift battery pan straight up and out.

9.

Remove the trunk pan.

a.

6.26 MAIN WIRE HARNESS

. Remove the two

fasteners securing the preload adjuster to the trunk
pan (13).

b.

Remove the shock reservoir fastener and retainer.
Push the reservoir aside to access the fastener.

c.

Remove remaining fasteners securing front trunk pan
to side tail sections.

d.

Remove remaining components on trunk pan as
needed.

10. Remove fan shroud.

Installation

1.

Install fan shroud. See

sm06807

Figure 2-210. Preload Adjuster with Reservoir Hose

Routing

2.

Install the trunk pan.

a.

See

6.26 MAIN WIRE HARNESS

. Install the two

fasteners securing the preload adjuster to the trunk
pan (13) and tighten to 36-60 in-lbs (4.1-6.8 Nm).

b.

Install the shock reservoir fastener and retainer and
tighten fastener to 80-88 in-lbs (9-10 Nm). Push the
reservoir aside to access the fastener.

c.

Install fasteners securing front trunk pan to side tail
sections and tighten to 72-96 in-lbs (8-11 Nm).

d.

Install the rear trunk pan fasteners and tighten to
48-72 in-lbs (5-8 Nm).

e.

Install remaining components on trunk pan as needed.

3.

Install battery pan and tighten fasteners to 72-96 in-lbs
(8-11 Nm) .

a.

See

2.49 AIR SCOOPS

Install ECM

(2).

b.

Connect rear brake light switch connector [121].

c.

Install fuse block and relay center (4).

d.

Install main harness and plastic grommet (6) from
battery pan.

NOTE

Before installing fasteners securing the nner ram air scoop to
the fuel tank/frame, it will be necessary to attach the Oxygen
Sensor wire to the inside of the scoop.

4.

Install fasteners securing the inner ram air scoop to the
fuel tank/frame and tighten to 12-36 in-lbs (1.4-4 Nm).

5.

Install fasteners securing the outer ram air scoop to the
inner ram air scoop and tighten to 22-26 in-lbs (2.4-3 Nm)
.

2-168 2010 XB Service: Chassis

«
...
246
247
248
249
250
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: KTM Power Parts Pages: 7

Venitex BARRIER

Brand: DELTA PLUS Pages: 2

Brand: paladin Pages: 2

Brand: Yamaha Pages: 126

Brand: Arai Helmet Pages: 12

Brand: BMW Pages: 205

Brand: MSW Pages: 11

VENTURA BIKE-PACK SYSTEM Series

Brand: DOLD Pages: 4

Brand: N-Com Pages: 36

Brand: Benelli Pages: 454

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 4

Brand: Beta Pages: 260

Brand: Royal Alloy Pages: 40

Brand: KTM Pages: 7

Brand: Vinz Pages: 22

Brand: Yingang Pages: 144

AVENGER 220 CRUISE

Brand: Bajaj Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands