Buell XB 2010 Service Manual Download Page 277 | Manualshive

Page: 277 / 714

background image

3.4

ENGINE ROTATION FOR SERVICE

GENERAL

The following process allows you to rotate engine down,
pivoting on rear isolator mount, in order to service components
in the top end.

NOTE

The engine does not need to be removed from chassis in order
to perform top end repairs.

DISASSEMBLY

NOTES

•

Before vehicle is placed on the lift it is necessary to remove
the chin fairing. See

2.50 CHIN FAIRING

.

•

Vehicle should be placed onto the lift with front tire placed
in the wheel vise in order to successfully perform this
procedure.

1.

Disconnect fuel pump electrical connector and run vehicle
until it is out of fuel. See

.

NOTES

•

This step is always performed in order to purge fuel lines.

•

The connection for fuel pump is just above the pump loc-
ated at the rear of the fuel tank on the left side of the
vehicle.

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

2.

Remove seat and disconnect battery cables from battery:
negative cable (black) first.

3.

Remove intake cover. See

2.38 INTAKE COVER

.

4.

Remove air filter base plate. See

4.3 AIR CLEANER

NOTE

When removing the left air scoop, the alternator and voltage
regulator harnesses and connections are secured to the bottom
of the air scoop with three cable straps. When removing the
right air scoop/shroud it will be necessary to remove the front
oxygen sensor connector from the scoop/shroud.

5.

Remove left and right air scoops. See

2.49 AIR SCOOPS

6.

Disconnect the front oxygen sensor.

NOTE

The velocity stack has a clamp ring securing it to the throttle
body.

7.

Remove throttle body velocity stack.

8.

Cover throttle body to prevent objects from falling into the
intake.

9.

See

. Disconnect fuel line (8).

10. Disconnect the throttle position sensor [88] (9).

11. Disconnect the fuel injector connectors [84 & 85] (6).

12. Disconnect the intake air control (IAC).

13. Disconnect the fuel pressure sensor (5).

2010 XB Service: Engine 3-9

«
...
275
276
277
278
279
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: Dakota Digital Pages: 6

Brand: oset Pages: 20

Easyrack 6617501 01 01

Brand: hepco & becker Pages: 4

Brand: Yamaha Pages: 98

Star XVS13CB(C)

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 145

ROADLINER XV19SW

Brand: Yamaha Pages: 444

Brand: Yamaha Pages: 494

Brand: Yamaha Pages: 94

Brand: ICON Vehicle Dynamics Pages: 4

Brand: R&G Pages: 9

Brand: Shark Pages: 92

Brand: Dakota Digital Pages: 14

Brand: CRATONI Pages: 44

Brand: Datatool Pages: 5

Brand: MARLINK Pages: 3

Brand: VOR Motori Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands