Buell XB 2010 Service Manual Download Page 208 | Manualshive

Page: 208 / 714

background image

2

1

3

sm03877

1.

Upper module

2.

Left module

3.

Right module

Figure 2-173. Front Modules: Ulysses

INSTALLATION

1.

Install right front module leaving single fastener loose.

2.

After installing the left front module and aligning with holes
in upper triple clamp, tighten previously installed single
fastener to 12-14 ft-lbs (16.3-19 Nm).

3.

Attach front brake line p-clamp to rear of right front module
and tighten fastener to 36-60 in-lbs (4-6.8 Nm).

4.

Install ignition switch. See

6.3 IGNITION/HEADLAMP KEY

.

5.

Install and connect instrument module. See

6.25 INSTRUMENT MODULE

.

6.

Connect turn signals. See

6.14 FRONT TURN SIGNALS

7.

See

. On Ulysses models, install upper

module. Tighten fasteners to 36-60 in-lbs (4-6.8 Nm).

8.

Connect speedometer.

9.

On Ulysses model, connect auxiliary outlet.

10. Install headlamp assembly and support bracket. See

2.26 HEADLAMP ASSEMBLY AND SUPPORT BRACKET

11. Install windshield and windscreen. See

2.48 WINDSHIELD

AND WINDSCREEN: LIGHTNING AND ULYSSES
MODELS

Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative (-) cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)

12. Connect battery cables to battery: positive cable (red) first.

Tighten to 60-70 in-lbs (6.8-7.9 Nm). See

.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

13. Install seat.

2-128 2010 XB Service: Chassis

«
...
206
207
208
209
210
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: 3M Pages: 26

Brand: Keis Pages: 2

Brand: APRILIA Pages: 163

Brand: hepco & becker Pages: 6

V-Gard 500 Series

Brand: MSA Pages: 2

Brand: KTM Power Parts Pages: 22

Brand: Yamaha Pages: 398

Brand: Yamaha Pages: 666

Brand: Yamaha Pages: 190

Brand: hepco & becker Pages: 3

Brand: DYNATEK Pages: 4

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 97

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 148

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands