Buell XB 2010 Service Manual Download Page 109 | Manualshive

Page: 109 / 714

background image

9

6

5

2

4

3

2

1

8

7

sm00523

7.

4.

1.

Rotor mount fastener (6)

Front brake springs (6)

Front axle

2.

8.

5.

Wheel bearing

Drive bushings (6)

Front wheel spacer

6.

3.

9.

Front brake rotor

Front wheel

Washer (6)

Figure 2-16. Front Wheel Assembly

Front Rotor Installation

1.

. Install new springs (4).

2.

Install new washers (9).

3.

Install new drive bushings (8) into rotor.

NOTE

Note the identifying mark of rotor is up and radius end of drive
bushing (8) toward center of wheel.

4.

Align reference dot on front rotor with the valve stem.

Do not re-use brake disc/rotor screws. Re-using these
screws can result in torque loss and damage to brake
components. (00319c)

5.

Install new rotor mounting fasteners (7) in a crisscross
pattern around the wheel to verify proper fitting between
rotor, fastener and bushing. Tighten to 25-27 ft-lbs (33.9-
36.6 Nm).

Rotor mounting fasteners must be seated into drive
bushings and drive bushings must be fitted into rotor
properly. Failure to comply can affect braking ability and
lead to brake failure which could result in death or serious
injury. (00499b)

INSTALLATION

1.

Raise front wheel to allow clearance for the caliper to
swing under and inside the front rotor.

NOTE

To prevent cosmetic damage to the wheel, center caliper
between spokes before installation.

2010 XB Service: Chassis 2-29

«
...
107
108
109
110
111
...
»

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Brand: Parkside Pages: 89

Brand: Parkside Pages: 28

Rebellion Electric Chopper 15130760

Brand: Razor Pages: 17

Two Fifty 250 cc

Brand: Mash Pages: 62

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 216

Brand: Yamaha Pages: 380

Brand: Yamaha Pages: 658

Brand: Yamaha Pages: 106

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: Dynafit Pages: 20

Brand: Shark Pages: 16

Brand: Yamaha Pages: 39

Roadliner XV1900AV

Brand: Yamaha Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands