manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

2.5

FRONT WHEEL

REMOVAL

1.

Place a scissor jack under jacking point and raise front
wheel off ground. For location of jacking point see

4.19 EXHAUST SYSTEM

.

NOTE

Do not operate front brake lever with front wheel removed or
caliper pistons may be forced out. Reseating pistons requires
caliper disassembly.

2.

Remove the right side lower fender fasteners. See

2.15 FENDERS

.

3.

See 

Figure 2-3

. Loosen front axle pinch fasteners (1) on

front fork.

4.

Remove axle (2).

NOTES

•

The front axle is left handed thread.

•

To prevent cosmetic damage to the wheel, center the
caliper between spokes before removal.

5.

See 

Figure 2-4

. Raise the wheel up until the rotor clears

the caliper and rotate the fork leg counterclockwise
allowing wheel clearance for removal.

6.

Remove wheel.

1

2

sm00510

1.

Front axle pinch fasteners (2)

2.

Axle (left handed thread)

Figure 2-3. Front Wheel Mounting

sm00511

Figure 2-4. Front Wheel Removal/Installation

DISASSEMBLY

TOOL NAME

PART NUMBER

WHEEL BEARING
REMOVER/INSTALLER KIT

B-43993-50A

FRONT WHEEL BEARING REMOVER
COLLET

B-43993-7, FROM
KIT PART NO. B-
43993-50A

WHEEL BEARING REMOVER AND
INSTALLER

HD-44060C

EXTREME PRESSURE LUBRICANT

J-23444-A

Bearing Removal

NOTE

On single disc wheels, always remove the brake disc side first.

1.

See 

Figure 2-5

. Remove wheel bearings using WHEEL

BEARING REMOVER/INSTALLER KIT (Part No. B-43993-

HOME

2010 XB Service: Chassis  2-23

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

ZERO GRAVITY SR Series Installation Manual preview
SR Series
Brand: ZERO GRAVITY Pages: 6
Öhlins SD 047 Mounting Instruction preview
SD 047
Brand: Öhlins Pages: 8
Öhlins prodrive SUR 3A00 Mounting Instructions preview
prodrive SUR 3A00
Brand: Öhlins Pages: 4
Öhlins HO 404 Mounting Instructions preview
HO 404
Brand: Öhlins Pages: 2
Öhlins HO 201 Owner'S Manual preview
HO 201
Brand: Öhlins Pages: 2
Öhlins FCX 0302 Mounting Instructions preview
FCX 0302
Brand: Öhlins Pages: 8
Öhlins DU 907 Mounting Instructions preview
DU 907
Brand: Öhlins Pages: 4
KTM F4303U1 Owner'S Manual preview
F4303U1
Brand: KTM Pages: 130
MRA 4025066171910 Mounting Instructions preview
4025066171910
Brand: MRA Pages: 9
X-lite X-901 Directions For Use Manual preview
X-901
Brand: X-lite Pages: 84
R&G BRG0015SS Fitting Instructions Manual preview
BRG0015SS
Brand: R&G Pages: 24
Honda CB600F Owner'S Manual preview
CB600F
Brand: Honda Pages: 110
Takegawa 02-01-0284 Instruction Manual preview
02-01-0284
Brand: Takegawa Pages: 2
Malossi 5518095 Manual preview
5518095
Brand: Malossi Pages: 24
R&G ECC0289R Fitting Instructions Manual preview
ECC0289R
Brand: R&G Pages: 9
EINHELL BG-SH 1 Original Operating Instructions preview
BG-SH 1
Brand: EINHELL Pages: 48
Memphis Shades 2320-0032 Mounting Instructions preview
2320-0032
Brand: Memphis Shades Pages: 2
Razor Crazy Cart XL Replacement Instructions preview
Crazy Cart XL
Brand: Razor Pages: 3

Brands by name

Popular brands

Load more brands