manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

2.4

WHEELS

GENERAL

Good handling and maximum tire mileage are directly related
to the care of wheels and tires. Regularly inspect wheels and
tires for damage and wear. If handling problems occur, see

1.22 TROUBLESHOOTING

 or refer to 

Table 2-18

.

See 

1.8 TIRES AND WHEELS

 for tire pressures. Keep tires

inflated to the recommended air pressure. Always balance the
wheel after replacing a tire.

Do not inflate tire beyond maximum pressure as specified
on sidewall. Over inflated tires can blow out, which could
result in death or serious injury. (00027a)

TROUBLESHOOTING

See 

Figure 2-2

. Check tire inflation pressure at least once each

week. At the same time, inspect tire tread for punctures, cuts,
breaks and other damage. Repeat the inspection before long
trips.

sm00110

Figure 2-2. Checking Tire Inflation Pressure

Table 2-18. Wheel Service: XB Models

REMEDY

CHECK FOR

Tighten front axle. See 

2.5 FRONT WHEEL

.

Loose axles.

Tighten rear axle. See 

2.6 REAR WHEEL

Replace wheel hub bearings.

Excessive side-play or radial (up-and-
down) play in wheel hubs.

Repair swingarm. See 

2.19 SWINGARM AND BRACE

.

Alignment of rear wheel in frame or with
front wheel.

Replace rims. See 

2.7 TIRES

 and 

2.8 CHECKING CAST RIM RUNOUT

.

Rims and tires out-of-true sideways;
should not be more than 0.080 in. (2.03
mm).

Replace rims. See 

2.7 TIRES

 and 

2.8 CHECKING CAST RIM RUNOUT

.

Rims and tires out-of-round or eccentric
with hub; should not be more than 0.090
in. (2.29 mm).

Replace. See 

2.7 TIRES

.

Irregular or peaked front tire wear.

Inflate tires to correct pressure. See 

1.8 TIRES AND WHEELS

.

Correct tire inflation.

Static balance may be satisfactory if dynamic balancing facilities are not available.
However, dynamic balancing is strongly recommended.

Correct tire and wheel balance.

Correct adjustment and replace pitted or worn bearings. See 

1.17 STEERING HEAD

BEARINGS

.

Steering head bearings.

Check for leaks. See 

2.16 FRONT FORKS

 (Firebolt/Lightning) or 

2.16 FRONT FORKS

(Super TT/Ulysses).

Damper tubes.

Check damping action and mounts. See 

2.23 REAR SHOCK ABSORBER

.

Shock absorbers.

Check for looseness. See 

2.19 SWINGARM AND BRACE

.

Swingarm bearings.

HOME

2010 XB Service: Chassis  2-21

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

LAZER Vertigo Owner'S Manual preview
Vertigo
Brand: LAZER Pages: 13
Öhlins SD 047 Mounting Instruction preview
SD 047
Brand: Öhlins Pages: 8
Öhlins prodrive SUR 3A00 Mounting Instructions preview
prodrive SUR 3A00
Brand: Öhlins Pages: 4
Öhlins HO 404 Mounting Instructions preview
HO 404
Brand: Öhlins Pages: 2
Öhlins HO 201 Owner'S Manual preview
HO 201
Brand: Öhlins Pages: 2
Öhlins FCX 0302 Mounting Instructions preview
FCX 0302
Brand: Öhlins Pages: 8
Öhlins DU 907 Mounting Instructions preview
DU 907
Brand: Öhlins Pages: 4
Dakota Digital MCL-30K-SPD Installation Manual preview
MCL-30K-SPD
Brand: Dakota Digital Pages: 7
METRAKIT MINI50 GP 2009 Owner'S Manual preview
MINI50 GP 2009
Brand: METRAKIT Pages: 53
hepco & becker 650949 01 01 Quick Start Manual preview
650949 01 01
Brand: hepco & becker Pages: 2
Suzuki 990D0-44G00-ALM Fitting Instructions Manual preview
990D0-44G00-ALM
Brand: Suzuki Pages: 24
Honda CBR300R 2013 Owner'S Manual preview
CBR300R 2013
Brand: Honda Pages: 61
IRC SGRACE-CUT Instructions preview
SGRACE-CUT
Brand: IRC Pages: 2
MOTO GUZZI Griso1200 8V Service Station Manual preview
Griso1200 8V
Brand: MOTO GUZZI Pages: 266
Denali MA11729 Manual preview
MA11729
Brand: Denali Pages: 5
Yamaha QT50 Owner'S Manual preview
QT50
Brand: Yamaha Pages: 39
Yamaha Roadliner XV1900AV Owner'S Manual preview
Roadliner XV1900AV
Brand: Yamaha Pages: 86
Yamaha ROADLINER XV19C Owner'S Manual preview
ROADLINER XV19C
Brand: Yamaha Pages: 95

Brands by name

Popular brands

Load more brands