manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

forcing screw, with the smaller diameter toward the hex
head.

2.

Insert the forcing screw through the wheel hub on the
opposite side of the wheel.

3.

See 

Figure 2-31

. Install the spacer (2).

NOTE

Center the spacer while installing the wheel bearing. Failure
to center the spacer could cause the bearing not to pull in
straight.

4.

See 

Figure 2-32

. Insert a new wheel bearing (1) squarely

into the hub, with the lettered side facing out (away from
the wheel).

5.

Slide the FRONT BEARING INSTALLER (Part No. B-
43993-9) (2) onto the forcing screw (3), with the smaller
diameter toward the bearing bore.

6.

Install a washer (4), bearing (5) and nut (6) onto the forcing
screw (3).

7.

While holding the forcing screw (3), tighten the nut (6) until
the bearing contacts the spacer.

2

1

sm00521

1.

Forcing screw

2.

Spacer

Figure 2-31. Install the Spacer

1

3

6

5

4

2

sm00522

1.

Wheel bearing

2.

Front wheel bearing installer

3.

Forcing screw

4.

Washer

5.

Bearing

6.

Nut

Figure 2-32. Install the Bearing

WHEEL BEARINGS: THREE BEARING
WHEELS

TOOL NAME

PART NUMBER

NICE BEARING

217801

BUELL WHEEL BEARING
INSTALLER/REMOVER

B-50019

SPACER

B50019-2

BEARING INSTALLER

B-50019-3

BEARING INSTALLER

B-50019-4

BEARING REMOVER

B-50019-5

BEARING INSTALLER CUP

B-50019-6

SPACER

B-50019-7

BOLT

B-50019-8

6" FORCING SCREW

HD-44060-4

BRIDGE

HD-44060-5

WHEEL BEARING INSTALLER AND
REMOVER

HD-44060-C

EXTREME PRESSURE LUBRICANT

J-23444-A

Removal: Brake Rotor Side

NOTE

Remove the brake rotor side bearing first.

HOME

2010 XB Service: Chassis  2-37

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Bajaj Pulsar N160 Owner'S Manual preview
Pulsar N160
Brand: Bajaj Pages: 55
R&G FI0054BK Fitting Instructions preview
FI0054BK
Brand: R&G Pages: 4
GAS GAS Pampera Service Manual preview
Pampera
Brand: GAS GAS Pages: 34
Honda CB600F Owner'S Manual preview
CB600F
Brand: Honda Pages: 110
R&G CP0466 Series Fitting Instructions Manual preview
CP0466 Series
Brand: R&G Pages: 9
Wedze IM 16 S Manual preview
IM 16 S
Brand: Wedze Pages: 63
Wolfman RTR4 Mounting Instructions preview
RTR4
Brand: Wolfman Pages: 3
yasuni TUB807-D57 Assembly Instructions Manual preview
TUB807-D57
Brand: yasuni Pages: 9
KREIDLER MP 9 Manual preview
MP 9
Brand: KREIDLER Pages: 4
Fekon 150-14 Owner'S Manual preview
150-14
Brand: Fekon Pages: 24
APRILIA 854239 Service Station Manual preview
854239
Brand: APRILIA Pages: 216
KOOFU CS-1 Instruction Manual preview
CS-1
Brand: KOOFU Pages: 24
Gemini gtrack 7855 MyBASIC User Manual preview
gtrack 7855 MyBASIC
Brand: Gemini Pages: 20
Yamaha FJR13AA Owner'S Manual preview
FJR13AA
Brand: Yamaha Pages: 114
Yamaha FJR1300R Owner'S Manual preview
FJR1300R
Brand: Yamaha Pages: 119
Yamaha FAZER FZS1000S Owner'S Manual preview
FAZER FZS1000S
Brand: Yamaha Pages: 104
Yamaha FAZER FZS600 Owner'S Manual preview
FAZER FZS600
Brand: Yamaha Pages: 108
Yamaha FJR1300 Service Manual preview
FJR1300
Brand: Yamaha Pages: 572

Brands by name

Popular brands

Load more brands