Belarus 3522.5 Operator'S Manual Download | Manualshive

Page: 234 / 340

background image

3522.5-0000010 OM

235

band of not less than 3 m width and also be provided with fire extinguishing means.

The tractor must be filled with fuel and lubricants by a mechanic way and with the

engine stopped. Use lighting at night time. It is not recommended to fill in tanks using
buckets. Carrying out repair operations in field conditions using electric/gas welding, clean
parts and assembly units from plant remains.

Prevent the manifold and muffler from getting dirty with dust, fuel, thatch, etc.
Avoid thatch winding around rotating parts of the implements coupled with the trac-

tor.

Washing parts and assembly units with kerosene or gasoline take care to exclude a

possibility of inflammation of flushing fluid vapor.

Do not operate the tractor in places subjected to fire risk with the hood and other

protective units removed from hot parts of the engine.

Do not use open fire to warm up oil in the engine sump, to fill in fuel tanks, to burn

out dirt in a radiator cell.

In case a fire bed occurs, pour some sand onto it, cover with canvas cloth, sack-

cloth or other dense texture. Use a carbon-dioxide fire extinguisher. Do not pour water
over burning fuel and oil.

Make sure there are no flammable materials near the exhaust manifold during en-

gine running.

Harvesting hay and thatch, operating at places with enhanced danger of fire, avoid

amassment of inflammable materials on a muffler guard and on gas links.

Turn the power disconnect switch off when finishing to operate the tractor.

https://tractormanualz.com/

«
...
232
233
234
235
236
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Brand: Mahindra Pages: 18

Craftsman 944.600940

Brand: Sears Pages: 60

Brand: Kioti Pages: 120

Verti-Comb 1800

Brand: Redexim Pages: 18

Brand: Gaggenau Pages: 24

Brand: PTR Pages: 67

Brand: matev Pages: 16

Brand: matev Pages: 19

Brand: matev Pages: 23

FPS-FKH-Kioti CS 2520

Brand: matev Pages: 28

FPS-FKH-Kioti CX 2510

Brand: matev Pages: 31

Brand: matev Pages: 34

Brand: matev Pages: 37

Brand: IMC Pages: 22

Brand: IMC Pages: 24

Brand: Branson Pages: 7

Brand: Branson Pages: 135

Brand: Branson Pages: 151

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands