Belarus 3522.5 Page 333 Operator'S Manual Download | Manualshive

Page: 333 / 340

background image

3522.5-0000010 OM

334

9. Tractor transportation and towing

9.1 Tractor transportation
Tractors are transported by railroad, motor vehicles or under its own power. How-

ever when a tractor is transported by motor vehicles or under its own power on public
roads, its transportation shall be agreed with road services as related to tractor bulkiness.

Engage the parking breaks for tractor transportation.
Fasten the tractor to the platform with four sling ropes.
Fasten one sling rope on each side to a nut located on rear wheel hub by one end,

and to binder bracket by another end. Also fasten one sling rope on each side of the trac-
tor to the FLL supporting bracket by one rope end and to binder bracket by another end.

During tractor loading/unloading use lifting mechanisms with load-carrying capacity

of at least 15 ton-force.

Tie steel ropes down to front axle beam and rear wheels semiaxle, as shown in the

scheme roping diagram in Figure 9.1.1.

For tractor roping the following accessories are:
- loops on the rope (or on other accessory) shall be put on semiaxles with lock nuts

and rear axles washers;

- rope hooks shall be put on front driving axle semiaxles.

Figure 9.1.1 – Tractor roping diagram

9.2 Towing of tractor

Towing of tractor is allowed at a speed of not more than 10 km/h for a distance of 5

km. Before starting tractor towing set the range selector lever to a “Neutral” position.

In order to connect a towing rope there is a towing yoke located on a supporting

bracket along with front ballast weights.

In case the tractor is towed without the front ballast weights, the towing rope shall

be fastened to the towing yoke located on a supporting bracket of a FLL.

In case the tractor is towed with no FLL and FPTO mounted, the towing rope shall

be fastened to the towing yoke located on the ballast weights.

THE TOWING SHACKLE MUST NOT BE USED TO LIFT THE TRACTOR!

ATTANTION: DURING TOWING OF THE TRACTOR OBSERVE THE TRAFFIC

REGULATIONS RIGIDLY!

https://tractormanualz.com/

«
...
331
332
333
334
335
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Brand: Sami Pages: 10

Brand: Dynapac Pages: 34

WEEKEND WARRIOR 6042

Brand: Maschio Pages: 46

Brand: Kellfri Pages: 8

Brand: New Holland Pages: 41

Brand: Milnor Pages: 49

Groom Master II 88009

Brand: Jacobsen Pages: 86

Brand: Zetor Pages: 182

Brand: Valtra Pages: 19

Brand: Valtra Pages: 51

Brand: Pottinger Pages: 27

Brand: Ingersoll-Rand Pages: 67

Brand: Iran Tractor Pages: 106

Brand: Iran Tractor Pages: 118

Brand: Iran Tractor Pages: 122

Brand: ASP Pages: 111

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands