Belarus 3522.5 Operator'S Manual Download | Manualshive

Page: 81 / 340

background image

3522.5-0000010

РЭ

82

2.21 Seat and its adjustments

2.21.1 General information
The seat has a mechanical suspension, consisting of two spiral torsion springs and a

gas charged shock absorber of two-directional operation. A “scissors”-type guiding mechanism
ensures a strictly vertical movement of the seat. A dynamic seat stroke is 100 mm.

ATTENTION: BEFORE STARTING TO OPERATE THE TRACTOR ADJUST THE SEAT TO

REACH THE MOST COMFORTABLE POSITION. CARRY OUT ALL ADJUSTMENTS WHEN STAYING
IN THE SEAT! THE SEAT IS CONSIDERED CORRECTLY ADJUSTED ACCORDING TO THE MASS IF
IT MOVES HALF OF THE STROKE UNDER THE OPERATOR'S WEIGHT (THE SUSPENSION
STROKE IS 100 MM)!

2.21.2 “BELARUS” seat adjustments

1 – handle to adjust according to the weight; 2 – handle for longitudinal adjustment; 3 –

handwheel to adjust the backrest tilt.

Figure 2.21.1 – “BELARUS” seat adjustments

The “BELARUS” seat has the following adjustments:
- adjustment according to the operator's weight. It is carried out by means of a handle 1

(figure 2.21.1) within the range from 50 to 120 kg. To adjust the seat for a bigger weight it is re-
quired to shift the pawl of the lever 1 into position “A” and tighten the springs with a reciprocal
movement. To adjust the seat for a smaller weight it is required to shift the pawl into position “

Б

”

and release the springs with a reciprocal movement.

- longitudinal adjustment. It is carried out by means of a handle 2 within the range of

±

80 mm from the middle position. To move the seat forward-backward it is required to pull the

https://tractormanualz.com/

«
...
79
80
81
82
83
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Brand: Ariens Pages: 44

Brand: Rankin Pages: 37

Brand: Case Pages: 96

Brand: Whirlpool Pages: 4

Brand: Whirlpool Pages: 4

Brand: Whirlpool Pages: 8

Brand: Whirlpool Pages: 8

Brand: Whirlpool Pages: 7

Brand: Whirlpool Pages: 8

Brand: Whirlpool Pages: 12

Brand: Whirlpool Pages: 12

Brand: Whirlpool Pages: 16

Brand: Whirlpool Pages: 16

GX900QPLQ - 15" Trash Compactor

Brand: Whirlpool Pages: 16

Techstar CVT MT525B Series

Brand: Challenger Pages: 248

MOTOR GRADERS G930

Brand: Volvo Pages: 10

G970, G976, G990

Brand: Volvo Pages: 17

Brand: Midwest Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands