manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Share
Download
Belarus 3522.5 Operator'S Manual Download Page 323

3522.5-0000010 OM

324

Continuation of the Table 7.3

а

Error
code

Cause of suspicion and malfunction

nature

Test and elimination method

81

The central spool of the distribu-

tion valve section does not shift
back in “neutral” position. Control by
the joystick or by the HLL POU can
not be executed. The central spool
is blocked in “lift” “lowering” or “float-
ing” position.

If the abovementioned failures

occur the error code “24” is indi-
cated once, and then code “81”  is
indicated permanently

Use manual control to shift the central
spool with effort not exceeding 450 N.
If this actions require more efforts that
the distribution valve section shall be
rinsed. In case these actions have no
beneficial effect, the section is subject
to replacement. When determination of
the position of the central spool is car-
ried out, it is forbidden to rotate it
around its axis

82

Before the controls are engaged,

the central spool of the section is in
the “lift” position. Control by the joy-
stick or by the HLL POU can not be
executed. The error code is indi-
cated in the damaged sections only
immediately after voltage supply.
The error code is indicated only if
the central spool of the section is in
the “lift” position before the controls
are engaged. If the spool is  in ”low-
ering” position, code “43” is indi-
cated

Disassemble the cabinet in the sec-

tion with electrical equipment. Check if
the inductive position sensor is prop-
erly fixed. Use manual control to shift
the central spool with effort not ex-
ceeding 450 N. If this actions require
more efforts that the distribution valve
section shall be rinsed. In case these
actions have no beneficial effect, the
section is subject to replacement.

When determination of the position

of the central spool is carried out, it is
forbidden to rotate it around its axis

83

Software error. In this case con-

trol  by  the  joystick  or  by  the  HLL
POU can not be executed

Reprogramming or replacement of

the damaged section is required

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands