Belarus 3522.5 Page 302 Operator'S Manual Download

Page: 302 / 340

3522.5-0000010 OM

303

6.5.3 Guidelines for safe use of leveling jacks and statement of places where they

shall be installed

To lift the tractor use leveling jacks, and after lifting insert backing blocks and limit

stops under the front axle beam, rear wheels semi-axles, or base components of the trac-
tor frame.

Places for a leveling jack installation on the tractor are marked by a sign shown in

Figure 6.5.1.

Figure 6.5.1 – Sign of a place for a leveling jack installation

To lift rear elements of the tractor set leveling jacks (or single jack) under the rear-

axle tube as illustrated in Figure 6.5.2.

Figure 6.5.2 – Scheme of leveling jacks installation for lifting of the rear elements of the tractor

To lift front elements of the tractor set leveling jacks (or single jack) under the front

driving axle beam as illustrated in Figure 6.5.3.

Figure 6.5.3 – Scheme of leveling jacks installation for lifting of the front elements of the trac-
tor

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Search results

Summary of Contents for 3522.5

Reviews:

Related manuals for 3522.5

Brands by name

Popular brands

Belarus 3522.5, Operator'S Manual

Search results

Summary of Contents for 3522.5

Reviews:

Related manuals for 3522.5

Brands by name

Popular brands