Belarus 3522.5 Page 138 Operator'S Manual Download | Manualshive

Page: 138 / 340

background image

3522.5-0000010

РЭ

139

Check and if necessary adjustment of pneumatic system single-wire brake valve ac-

tuator "A" (figure 3.10.2) should be made after adjustment operations of pedal brakes and
control adjustments of parking brake.

ATTENTION: MAKE ADJUSTMENT OF SINGLE-WIRE BRAKE VALVE ACTUA-

TOR AT NOT PRESSED PEDALS OF SERVICE BRAKES AND COMPLETELY
SWITCHED OFF PARKING BRAKE!

Before check and adjust pneumatic system single-wire brake valve actuator put a

tractor on flat ground. The engine should be switched off. Lock the wheels fore and aft with
stop pieces which will exclude spontaneous moving of the tractor.

Check and, if it is necessary, adjustment of brake valve actuator "A" (figure 3.10.2)

of single-wire pneumatic drive should be made in the following order:

- attach manometer with scale not less than 1 MPa to connecting head (with black

cover) of tractor pneumatic drive;

- start the engine and fill tank with air till pressure of 0,77… 0,8 MPa according to

pneumatic system air pressure indicator, situated on dashboard. Stop the engine;

- air pressure according to manometer attached to connecting head should not be

lower than 0,77 MPa. If the pressure is lower, do the following operations:

1. check the length of assembled rod 4 (figure 3.10.2).
2. length of rod should provide its free (without tension) connection to the lever7

by pin 2. If it is necessary, adjust its length by turning of fork 6. Lock fork 6 with nut 5.

- if air pressure according to manometer attached to connecting head, has not

reached necessary value, replace the brake valve.

ATTENTION: AT CORRECTLY ADJUSTED BRAKE VALVE "A" AND ITS ACTUA-

TOR THE PRESSURE SHOULD FALL TILL ZERO AT INTERCONNECTED BRAKES
PEDALS TRAVEL OF 100 … 120 MM OR AT FIXING OF PARKING BRAKE ON THE
FOURTH-FIFTH TOOTH OF THE SECTOR!

3.10.2.2 Check and adjustment of pneumatic system two-wire brake valve actuator
Check and, if it is necessity, adjustment of pneumatic system two-wire brake valve

actuator “

Б

” (figure 3.10.2) should be made after adjustment operations of pedal brakes

and control adjustments of parking brake.

ATTENTION: MAKE ADJUSTMENT OF TWO-WIRE BRAKE VALVE ACTUATOR

AT NOT PRESSED PEDALS OF SERVICE BRAKES AND AT COMPLETELY
SWITCHED OFF PARKING BRAKE!

Before check and adjust pneumatic system two-wire brake valve actuator put

a tractor on flat ground. The engine should not run. Lock the wheels fore and aft with stop
pieces which will exclude spontaneous moving of the tractor.

https://tractormanualz.com/

«
...
136
137
138
139
140
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Brand: Rankin Pages: 30

Brand: Komatsu Pages: 8

Brand: Poulan Pro Pages: 52

Techstar CVT MT525B Series

Brand: Challenger Pages: 248

Brand: Branson Pages: 132

Brand: CAMSO Pages: 20

Brand: Daedong Pages: 246

Brand: Yanmar Pages: 4

Brand: ryan Pages: 67

Brand: Yazoo Pages: 8

Brand: Valtra Pages: 31

Brand: Valtra Pages: 51

PROXIMA POWER Z90 2012

Brand: Zetor Pages: 222

Brand: Bolens Pages: 19

Brand: Bolens Pages: 104

Brand: Textron Pages: 182

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands