Belarus 3522.5, Operator'S Manual

Page: 218 / 340

3522.5-0000010
РЭ
219
- raise the plough from the working position by means of the joystick 2 (figure 4.2.2),
operating over the section No3;
- decrease the plough width to the min. by means of the joystick 1, operating over
the section No2;
- turn the plough from the extreme left position to the extreme right position by
means of the joystick 1, operating over the section No1;
- set a required width by means of the joystick 1, operating over the section No2;
- lower the plough into the working position by means of the joystick 2, setting the
“floating” condition over the section No3 (herewith the indicator 9 (figure 4.2.3) will display
“FL”);
- repeatedly press the buttons 13, 14, 15 (figure 4.2.3) to select sections No3, No2,
No1 of the hydraulic distributor EHS (record over the sections is finished);
- to finish the programming press the button 4 of the recorded program No1.
The program No2 provides automatic implementation of the following operations:
- plough uplift from its working position;
- decrease of plough width to a min. one;
- plough overturn into a contrary extreme position (from left to right);
- increase of plough width to a required one;
- plough lowering into the working position.
To record the program No2 it is required to do the following:
- actuate the OPU of the HLL (if it is off), pressing the button 1 (figure 4.2.3);
ATTENTION: BEFORE RECORDING THE PROGRAM No1 IT IS REQUIRED TO
SET THE PLOUGH INTO A CERTAIN CONDITION IN A MANUAL MODE (THE PLOUGH
SHALL BE TURNED TO THE RIGHT INTO ITS EXTREME POSITION, SET A RE-
QUIRED WIDTH, LOWER THE PLOUGH INTO THE WORKING POSITION)!
- press and hold the button 3 (program No2). After two seconds the OPU of the HLL
produces an acoustic signal, turns on the indicator 6 in the mode of fast blinking and
passes into the programming mode (storing manipulations made with the joystick);
- press the buttons 13, 14, 15 to select sections No3, No2, No1 of the hydraulic dis-
tributor EHS, respectively. The annunciators 10 indicating uplift and lowering of these sec-
tions shall simultaneously turn on in the mode of slow blinking;
- raise the plough from the working position by means of the joystick 2 (figure 4.2.2),
operating over the section No3;
- decrease the plough width to the min. by means of the joystick 1, operating over
the section No2;
- turn the plough from the extreme right position to the extreme left position by
means of the joystick 1, operating over the section No1;
- set a required width by means of the joystick 1, operating over the section No2;
- lower the plough into the working position by means of the joystick 2, setting the
“floating” condition over the section No3 (herewith the indicator 9 (figure 4.2.3) will display
“FL”);
- repeatedly press the buttons 13, 14, 15 (figure 4.2.3) to select sections No3, No2,
No1 of the hydraulic distributor EHS (record over the sections is finished);
- to finish the programming press the button 3 of the recorded program No2.
ATTENTION: MAX. POSSIBLE DURATION FOR EACH PROGRAM RECORD
SHALL NOT EXCEED 200 SECONDS!
Taking into consideration the novelty of the joystick control, programming peculiari-
ties and lack of experience when making programs, for the first time before the beginning
of the programming process it is recommended to study a manual for the implement or the
machine coupled and also to build up a sequence diagram of joystick control (algorithm of
a program) with indication of directions of joystick movements. This will allow to reduce
time for technological operations in implement or machine control in the working process.
https://tractormanualz.com/