Belarus 3522.5 Operator'S Manual Download | Manualshive

Page: 272 / 340

background image

3522.5-0000010 OM

273

6.4.1.13 Task 12. Inspect/clean position sensor control gear of FLL
Ensure that the control gear 1 (Figure 6.4.5) is clean by means of a position sensor

of FLL, and ensure that the FLL components, being close to the operating control gear, are
in running order also. Clean it if it is clogged.

1 – control gear; 2 – frame of the lower links of the FLL.

Figure 6.4.5 – Cleaning of the control gear by means of the position sensor of the FLL

ATTENTION: WHEN THE TRACTOR IS OPERATED WITH A FRONT LIFT LINK-

AGE, THERE SHALL BE NO SOIL, SNOW, ICE AND ETC., ON THE POSITION SEN-
SOR CONTROL GEAR AND ON THE LOWER LINKS FRAME OF THE FRONT LIFT
LINKAGE!

6.4.1.14 Task 13. Check breaks functioning in running order, the engine, steering,

light/alarm devices operability

The following tractor operating conditions shall be ensured:
- the engine shall percolate in all modes;
- control elements, light warning and acoustic alarm devices shall be properly oper-

ating;

- simultaneous engagement of the right and left service brake.
In case the abovementioned conditions were not observed adjust as required or

perform repair of the required tractor systems.

6.4.1.15 Task 14. Drainage of the condensate water from the pneumatic system

balloon

To condensate drainage from the both balloons 2 (Figure 6.4.6) of the pneumatic

system pull the ring drain valve ring 1, installed on each balloon towards the horizontal di-
rection of any side and hold it until full drainage of condensate.

1 – ring; 2 – pneumatic system balloon.

Figure 6.4.6 – Drainage of the condensate water from the pneumatic system balloon

6.4.1.16 Task 15. Drainage of the condensate water from the radiator tanks of CAC
Operation shall be carried out during the autumn and spring period in every 8-10

hours of the tractor operation or in shift time basis, and in spring and summer period – in
every 125 hours of the tractor operation.

In order to drainage the condensate water from the radiator tank of the engine CAC

it is necessary to perform the following actions:

- turn off two plugs 5 (Figure 3.1.3) in the bottom of the CAC radiator 1;
- let the condensate drain away;
- screw the plug 5.

https://tractormanualz.com/

«
...
270
271
272
273
274
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Brand: Kellfri Pages: 8

TRANSCAR Series

Brand: GOLDONI Pages: 154

Brand: MTD Pages: 37

Brand: New Holland Pages: 41

Brand: ryan Pages: 67

FORTERRA HSX 100 2014

Brand: Zetor Pages: 250

Brand: Husqvarna Pages: 36

Brand: Husqvarna Pages: 18

Brand: New Holland Pages: 9

Brand: Viking Pages: 10

Brand: Harvest TEC Pages: 20

Brand: Case IH Pages: 24

Brand: ASV Pages: 68

Brand: Tanco Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands