manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Share
Download
Belarus 3522.5 Operator'S Manual Download Page 197

3522.5-0000010 

РЭ

198

3.24  Cab air conditioning and heating system

The cab air conditioning and heating system is intended for development and keep-

ing of normal microclimate in the tractor cab.   The air conditioning system consists of two
circuits – heating and cooling. The system diagram is shown in figure 3.24.1.

The cooling circuit include compressor, condenser, filter-drain with pressure sensor,

monobloque of evaporator and of heater radiator (heater/cooler), heater/cooler fan, con-
necting hoses with quick-couplings set, electric cables, air filters, regulator of cold air and
fan switch. The heating circuit is amended by horses, connected with engine cooling sys-
tem of the tractor and with shut-off valve.

Figure  3.24.1 – Cab air conditioning and heating system

The compressor 7 (figure 3.24.2) is located on the left at the bottom part of the engine,
condenser 8 is in front of CAC radiator, filter-drain 1 is on condenser frame, pressure sen-
sor is on filter-drain 1, heater-cooler 5 is under the roof above ventilation  box panel, regu-
lator of cold air and fan switch is located on upper box panel , service valves are on fittings
near to the compressor 7 and filter-drain 1.

Quick coupling on horses
between cab and filter-drain

To engine
cooling system

Filter-drain

Horse Din 6

From engine
cooling system

Horse Din 10

Compressor

Condenser

Horse Din 13

Quick coupling on
horses   between cab and
compressor

Heater valve

Heating section of
radiators monobloque

Evaporator
 (cooling section of
radiators monobloque)

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands