manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Share
Download
Belarus 3522.5 Operator'S Manual Download Page 23

3522.5-0000010 

РЭ

24

Instruments are a combination of devices; these are an integrated indicator; pilot

lamps (glow lamps and light emitting diodes), located on the block of pilot lamps, on the
control panel of electronic block of complex electronic control system and on the combined
electronic panel.

1.4 Vibration level at the operator's working place of the tractor “BELARUS-3522.5”

The vibration level at the operator's seat complies with the Council Directive

78/764/

ЕEС

. Values for the vibration level are given in the EU type approval on each type

of a seat.

1.5 Noise level at the operator's working place of the tractor “BELARUS-3522.5”

Noise level at the operator's workplace conforms to Directive 2009/76/

ЕС

, Appendix

2, and does not exceed the value 86 dB (A). External noise level conforms to Directive
2009/63/

ЕС

 and does not exceed the value 89 dB (A).

1.6 Tractor marking

Metal nameplate is fixed at the rear of the cab on the right side, as shown in fig.

1.6.1.

Additionally the tractor serial number is applied by means of percussion on the right

lateral surface of the beam.

Figure 1.6.1 – Place of application the tractor nameplate

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands