Belarus 3522.5 Page 83 Operator'S Manual Download | Manualshive

Page: 83 / 340

background image

3522.5-0000010

РЭ

84

2.21.3 Seat installation for operation on reverse

1 – clamp; 2 – jaw; 3 – handle; 4 – clamp.

Figure 2.21.2 – Seat installation for operation on reverse

Seat installation for operation on reverse is carried out in the following order:
- release clamps 1 (figure 2.21.2) and take them aside, exempting jaws 2 of the up-

per base of the uplift mechanism;

- pulling a handle 3 up, unlatch the rotation mechanism and rotate the seat by 180°;
- applying force up and forward, move the seat to the extreme position against the

stop;

- carry clamps 4 into the jaws 2 and screw them in against the stop;
The seat installation for operation on forward motion is carried out in a reverse or-

der.

Seat adjustments on reverse are carried out in the same way as on forward motion.

on reverse

on forward motion

https://tractormanualz.com/

«
...
81
82
83
84
85
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

UpFront STS 12 Combo

Brand: Hagie Pages: 149

Brand: Rankin Pages: 30

Brand: Ventrac Pages: 87

Brand: AVANT Pages: 18

Brand: AVANT Pages: 24

Brand: Daedong Pages: 196

Brand: MTD Pages: 8

Brand: Grammer Pages: 85

Brand: Grammer Pages: 85

Brand: Escorts Pages: 73

Brand: Agromehanika Pages: 90

Brand: Agromehanika Pages: 245

Brand: Toro Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands