Belarus 3522.5 Operator'S Manual Download | Manualshive

Page: 184 / 340

background image

3522.5-0000010

РЭ

185

Electronic part of rear lift linkage control include the following components:
- RLL control unit 1 (figure 3.19.1);
- remote buttons 5 of RLL control;
- electronic control unit 2;
- force sensors 10 and 11 of rear lift linkage;
- RLL position sensor 7;
- electromagnetic valves of lowering 8 and uplift 9;
- connecting harness with electrical connectors 4 and 6;
- safety device of RLL ECS 3, situated in PASU.

Electronic part of rear lift linkage control operates in following order. After engine

start supply voltage goes to electronic control unit 2 of RLL ECS. Electronic control unit
inquire sensors, system controls and after analysis gives necessary commands to elec-
tromagnets of the regulator. The system is controlled either with a help of control unit 1
situated in the cabin or with a help of remote control buttons 5, situated on fenders of rear
wheels.

According to position sensor the electronic control system identify the position of

RLL relative to the tractor and at position control ensure keeping of mounting implement in
the defined position relative to the tractor.

According to force sensors the RLL control electronic system determine the force

applied during operation to lift linkage in horizontal axial direction from coupled implement.
At draft control the tillage depth is kept in proportion to created resistance force of imple-
ment. Therefore at tillage e.g. in the mode of draft control, RLL ECS receiving signals from
force sensors shallow up the implement of the tight soil and put the implement deeper in
soft soil.

At combined control the RLL control electronic system take into account the signals

from position and force sensors in proportion to the mode of control set by selector handle
2 (figure 2.14.1).

Note – The rules of RLL control are described in subsection 2.14 “Rear lift linkage

control”. The electric circuit diagram of real lift linkage control is given in subsection 7.2.
“Possible failures in the electronic control system of RLL and FLL guidelines for trouble-
shooting”.

https://tractormanualz.com/

«
...
182
183
184
185
186
...
»

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Brand: Belarus Pages: 125

Brand: Cub Cadet Pages: 2

Brand: Bad Boy Pages: 128

WEATHERBRAKE 307022172

Brand: Femco Pages: 7

T2 Versu Series

Brand: Valtra Pages: 36

Brand: Yanmar Pages: 6

Brand: Ventrac Pages: 39

Brand: Thwaites Pages: 24

Brand: Soucy Pages: 84

Brand: Soucy Pages: 154

Brand: Gravely Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands