manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Share
Download
Belarus 3522.5 Operator'S Manual Download Page 245

3522.5-0000010 OM

246

5.3.3 Front three-point lift linkage
Front lift linkage with dimensions corresponding to standard size “LL-2”, is similar on

critical parameters to the rear lift linkage. Front lift linkage is designed for the following pur-
poses:

- forming of combined units (tiller is in front of the machine, and seeder is behind

and etc.);

- forming of echelon linkage mounting (front and side-cut mower and etc.);
- transportation of implements detached from the combined units located in the rear

end during long-distance transportation;

- for mounting of front hanging ballast.

Front lift linkage of a tractor is used with tilling machines only in a propelling condi-

tion, FLL is not designed for use with tilling machines on reverse.

IT IS PROHIBITED TO OPERATE FLL WITH LOGGING BLADES, AND FOR

JACKING OF TACTOR FRONT ELEMENT.

Note – Rules on coupling of implements with FLL, guidance on changing of FLL op-

erating position into the transport position, and also the general information about the de-
sign of FLL are set forth in subsection 3.20 “Front lift linkage”.

Figure 5.3.4 – Front lift linkage diagram

Scheme of installation of linkage-mounted ballast weights assembled with mounted

bracket to FLL is shown in Figure 5.3.4

а

. Information about installation of linkage-mounted

ballast weights to FLL is shown in Table 5.2

а

.

Figure 5.3.4

а

 – Scheme of installation of linkage-mounted ballast weights to FLL

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands