manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Share
Download
Belarus 3522.5 Operator'S Manual Download Page 120

3522.5-0000010 

РЭ

121

3.6.6 Check and adjustment of play in differential tapered bearings

Axial play in the differential tapered bearings shall be 0,1 to 0,15 mm. Trying shims

2 (figure 3.6.4) under a cover 1, and if necessary under a cover 4, adjust bearing play.

The axial play shall be checked when moving the differential in axial direction with

application of force from 500 to 600 N.

The differential shall turn without seizure. The adjustment shall be carried out on the

rear axle body without the final drives 2 (figure 3.6.1) and the plate 1 in the rear axle as-
sembly. When carrying out adjustment turn the differential in bearings so that the rollers
took their position in cages.

1 – left cover; 2 – shims; 3 – bolt; 4 – right cover.

Figure 3.6.4 – Differential in rear axle body

3.6.7 Check and adjustment of the master pair backlash

The master pair backlash shall make 0,25 to 0,5 mm, the backlash variation shall

not exceed 0,2 mm for one pair. The contact pattern shall be not less than 50% of the sur-
face with impress location in the middle part of the tooth.

The backlash shall be adjusted by moving a certain amount of washers from under

the cover 4 (figure 3.6.5) under the cover 1 or vice versa, without changing their total num-
ber.

Before mounting the plate 3 ready-assembled with a drive gear of the master pair to

the axle body, check and if necessary set an installation dimension of the plate equal to
380±0,1 mm at the cost of changing the number of shims 4 (figure 3.6.6).

When mounting the plate pay attention to a position of the outer ring of a double-

row spherical bearing 9 (figure 3.6.6), turning and displacing on rollers. To prevent dis-
placement of the outer ring use a fixture, which centers the bearing outer ring.

ATTENTION: REPLACE THE MASTER PAIR GEARS ONLY AS A SET. THE MASTER

PAIR GEARS SHALL HAVE IDENTICAL NUMBERS!

ATTENTION: DIFFERENTIAL BODY, DIFFERENTIAL COVER AND LOCK BODY

SHALL BE REPLACED ONLY AS A SET. THE BODIES SHALL HAVE IDENTICAL NUM-
BERS!

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands