manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Looking for the Belarus 3522.5 Operator's Manual? Look no further! Our website offers a free download of this essential manual, providing detailed instructions and guidance for operating your Belarus 3522.5. Visit manualshive.com to access this manual and maximize your product's potential.

Share
Download
background image

3522.5-0000010 

РЭ

214

Before movement start determine the necessary speed of the tractor  movement.

The speed diagram of the tractor BELARUS-3522.5  with base design tyres is given in
instruction table on right glass in the cab and also in subsection 2.13.4. “Tractor velocity
diagramm”.

To put the tractor in motion the following shall be done:
- reduce engine rpm speed;
- set the necessary mode,  pushing the button of gear shifting mode selection. The mode

set will be displayed on indicator of gear shifting mode;

-  depress the clutch pedal;
- set the necessary GB range with a help of range selector lever according to the

scheme on lever handle, setting prelimitary mode “breaking”. When the mode “breaking” is
ON the digital indicalor displayes sympol “P”.  After installation of desired range release a
button    of “breaking” mode switching on.

- set the necessary GB range with a help of josticks for gear shifting according to

the instruction table situated near to the joystick. Herewith on digital indictor appers first
number of engaged gear, then will be activated corresponding annunciator of  gear en-
gagement.

- disengage parking break, release slowly clutch pedal increasing at the same time

fuel  delivery. The tractor starts to move.

If you need to switch on the creeper, please follow the instructions given in the sub-

section 2.13.3 “Creeper control”.

IT IS FORBIDDEN TO START MOVEMENT WITH BIG TRACTION LOAD!

IT IS FORBIDDEN TRACTOR MOVEMENT WITH OPEN DOOR!

ATTENTION: AT TRACTOR STARTING MAKE SURE THAT THE PARKING

BREAK IS DISENGAGED!

ATTENTION: SWITCH ON THE RANGE ONLY AFTER ¨BREAKING¨ MODE OF GB

SWITCHING ON!  

ВКЛЮЧАЙТЕ  ДИАПАЗОН  ТОЛЬКО  ПОСЛЕ  ВКЛЮЧЕНИЯ  РЕЖИМА

«ПОДТОРМАЖИВАНИЯ

» 

КП

! RANGE SWITCHING MAKE THROUGH NEUTRAL POSI-

TION WITH SWITCHING ON OF THE GB ¨BREAKING¨ MODE!

ATTENTION: SETTING OF GB RANGE IN NEUTRAL POSITION MAKE AFTER

GB SETTING ON GEAR ¨0¨!

ATTENTION: SWITCH ON THE RANGE ONLY AT STOPPED TRACTOR WITH

FULLY DEPRESSED PEDAL CLUTCH! RANGE SWITCHING DURING TRACTOR
MOVEMENT IS FORBIDDEN!

ATTENTION: IT IS ALLOWED TO ESCAPE THE CONDITION “GEARS DISEN-

GAGED” (GEAR «0») ONLY WHEN CLUTCH PEDAL IS FULLY PRESSED AT FOR-
WARD MOTION AND AT REVERSE MOTION AT FULLY PRESSED CLUTCH PEDAL
OF REVERSE CONTROL POST!

ATTENTION: MAKE GEAR SHIFTING WITHIN ONE RANGE DURING TRACTOR

MOVEMENT NOT PRESSING CLUTCH PEDAL!

ATTENTION: DON’T HOLD THE FOOD ON CLUTCH PEDAL DURING TRACTOR

OPERATION, BECAUSE IT CAN LEAD TO CLUTCH SLIPPING, ITS OVERHEATING AND
FAILURE!

ATTENTION: AT ENGAGED DIFFERENTIAL LOCK THE TRACTOR MOVEMENT

SHOULD NOT EXCEED 13 KMH!

ATTENTION: AT OPERATION ON HARD SURFACE IT IS NECESSARY TO

SWITCH OFF FDA DRIVE TO AVOID INCREASE WEAR OF FRONT WHEELS!

ATTANTION: TRACTOR OPERATION WITH EMPTY ADBLUE TANK (UREA) IS

NOT ALLOWED! WHEN ON MONITOR APPEARS INFORMATION ABOUT CRITICAL
LEVEL OF ADBLUE REAGENT (UREA) IN THE TANK, IT IS NECESSARY TO FILL THE
TANK WITH ADBLUE REAGENT.

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

Mahindra '16' Series Operator'S Manual preview
'16' Series
Brand: Mahindra Pages: 140
New Holland Boomer 20 Service Manual preview
Boomer 20
Brand: New Holland Pages: 41
GOLDONI C55 Operation And Maintenance preview
C55
Brand: GOLDONI Pages: 109
MTD 19A70041OEM Installation Manual preview
19A70041OEM
Brand: MTD Pages: 2
New Holland TI4.100 RS Service Manual preview
TI4.100 RS
Brand: New Holland Pages: 51
Fort 300W Instructions For Use And Maintenance Manual preview
300W
Brand: Fort Pages: 80
McCulloch M53-140W Instruction Manual preview
M53-140W
Brand: McCulloch Pages: 20
Broan Elite 15BLEXF Service Manual preview
Elite 15BLEXF
Brand: Broan Pages: 36
GE 165D4700P385 Owner'S Manual preview
165D4700P385
Brand: GE Pages: 24
Werner & Weber MPC-A Operation Manual preview
MPC-A
Brand: Werner & Weber Pages: 28
MTZ K-744R1 Operating Instruction preview
K-744R1
Brand: MTZ Pages: 202
MTZ 1220.1 Operator'S Manual preview
1220.1
Brand: MTZ Pages: 244
GOLDONI JOKER 10 DS Operation And Maintenance preview
JOKER 10 DS
Brand: GOLDONI Pages: 60
GOLDONI 20 Operation And Maintenance preview
20
Brand: GOLDONI Pages: 122
GOLDONI 2070 Operation And Maintenance preview
2070
Brand: GOLDONI Pages: 168
GOLDONI 26RS Operation And Maintenance preview
26RS
Brand: GOLDONI Pages: 200

Brands by name

Popular brands

Load more brands