manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Share
Download
Belarus 3522.5 Operator'S Manual Download Page 145

3522.5-0000010 

РЭ

146

3.11.3 Magnetic Filter

The magnetic filter (figure 3.11.4), intended for oil separation from ferromagnetic particles
of transmission hydraulic system. It is situated to the right along tractor movement on GB
cover of creeper control. The filter consists of the case 2 on which is mounted cover 1 with
four magnet traps 3.

1 – cover; 2 – casing; 3. magnet trap.

Figure 3.11.4 – Magnetic filter

3.11.4 Electrohydraulic Transmission Hydraulic System Distributor

Electrohydraulic transmission hydraulic system distributor is intended for GB and rear

axle differential lock friction clutches control

The

distributor is mounted on top plane of clutch

casing. In distributor casing 1 (figure 3.11.5) are screwed:

- six distributors 3 for control of six gears of GB;
- distributor of rear axle differential lock;
- distributor marked «

ПВМ

»(it means FDA) is not used;

- seven oil pressure sensors 4 in GB and rear axle differential lock friction clutches;
- oil pressure indicator sensor 2 in transmission hydraulic system.

1 – casing; 2 –pressure indicator sensor; 3 –distributor; 4 – pressure sensor.

Figure 3.11.5 – Electrohydraulic transmission hydraulic system distributor

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands