Belarus 3522.5 Operator'S Manual Download

Page: 121 / 340

3522.5-0000010

РЭ

122

ATTENTION: CAST IRON RINGS 5 (FIGURE 3.6.5) SHALL BE MOUNTED (IN

ORDER TO PREVENT RING DAMAGE DURING ADJUSTMENTS) AFTER ALL AD-
JUSTMENTS HAVE BEEN CARRIED OUT WITH THE FINAL MOUNTING OF THE
COVER 4!

1 – left cover; 2 – shims; 3 – plate ready-assembled with drive master pair; 4 – right

cover; 5 – cast iron rings.

Figure 3.6.5 – Differential and plate ready-assembled with drive gear of master pair

in rear axle body

3.6.8 Check of main drive gears for accuracy of engagement according to

contact pattern

POSITION OF CONTACT

PATTERN ON DRIVEN GEAR

Front motion Rear motion

WAY TO REACH CORRECT

GEAR ENGAGEMENT

__________________________

CORRECT GEAR ENGAGEMENT

WHEN CHECKED UNDER

SMALL LOAD

______________________________

MOVE THE DRIVE GEAR TO-

WARDS THE DRIVEN GEAR

_____________________________

MOVE THE DRIVE GEAR OFF

THE DRIVEN GEAR

_____________________________

MOVE THE DRIVEN GEAR OFF

THE DRIVE GEAR

_____________________________

MOVE THE DRIVEN GEAR TO-

WARDS THE DRIVE GEAR

SCHEME

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Search results

Summary of Contents for 3522.5

Reviews:

Related manuals for 3522.5

Brands by name

Popular brands

Belarus 3522.5, Operator'S Manual

Search results

Summary of Contents for 3522.5

Reviews:

Related manuals for 3522.5

Brands by name

Popular brands