Atex AR950 Operation Manual Download Page 21

Page: 21 / 106

Explanation of Picture Labels

Points on Use

●

0675-912-031-0

①

When refueling, stop the engine,

remove the key.

②

Fuel : Unleaded gasoline

Don’t bring a

re source closer,

as the fuel may ignite.

●

0675-912-032-0

The cover may suddenly close due to
gravity, pinching parts of your body and
causing injury.
Don’t open the engine cover on slope.

●

1705-902-006-0

The HST fan is operating .
Don’t bring your hands and feet close by while
the engine is running.

●

0674-916-034-0

①

The blade is turning.

Don’t bring your hands and feet close by while the engine is running.

②

Bush and stones scatter during work.

Keep people away from the machine.

① ②

0675-912-032-0

① ②

●

1728-903-003-0

Do not throw the battery into a trash can.
Recucle the battery according to the rules speci

by the local government.

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands