Atex AR950 Operation Manual Download Page 8

Page: 8 / 106

Point on Use

Precations for Use

This chapter explains the items the user must pay attention to in order to use the
machine ef

ciently and safely. Read the information provided below and work safely.

■

Operator Conditions

1. Wear clothes suitable for working on the

Ride-on Bush Cutter . Loose clothes may be
dragged into the rotating parts, while improper
shoes may slip, creating a very dangerous

situation. Also wear a helmet and appropriate

protective gears.

2. Anyone under the in

uence of alcohol or tired

from overwork or pregnant woman, child or
any other inexperienced person shall never be
allowed to operate the Ride-on Bush Cutter.
Doing so may result in an unexpected

accident. Only a person with a healthy mind

and body should operate the Ride-on Bush
Cutter.

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands