Atex AR950 Operation Manual Download Page 77

Page: 77 / 106

How to Work

■

Replacing the Brake Shoe

1. Depress the parking brake pedal and “Unlock”

the parking brake.

2. Remove the guard pipe and take out four bolts

(M6) from the back plate.

3. Remove the brake shoe from the back plate, and

then replace it with the new one. If brake drum
is replaced with the new one at the same time,
the life time of brake shoe is longer.

4. Assemble the back plate and tighten four

mounting bolts (M6) while applying a force to
the arrowed direction.

5. Install the cable (brake) and adjust the brake.

(Refer to p.69 of this manual)

●

If the parking brake remains ineffective after adjusting the brake

or there is no longer an adjustment allowance, the brake shoe

must be replaced. Replace the brake shoe immediately; otherwise,

unexpected accident may occur.

Warning

●

When replacing the brake shoe, make sure to park the machine on

at and rigid

ground. Then, stop the engine, and put chocks (wheel stops) underneath the
tires.

Guard pipe

Back plate

bolt (M6) x 4 pcs

Brake drum

Brake shoe

Brake arm

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands