Atex AR950 Operation Manual Download Page 31

Page: 31 / 106

Name and Function of Each Part

■

Cutting-blade Cover Wash Pipe

Connect a water hose to this pipe when washing the in-
terior of the cutting-blade cover after work.

■

Engine Cover

Warning

●

The operator or any other people may cause injury

sandwiched between the engine cover.

When opening the engine cover, be sure to do it on

at ground

without being blowed by strong wind.

Open the engine cover for easy access to the engine for

cleaning, inspection and maintenance.

1. Tilt the seat forward and remove the knob

bolts

at the rear left-hand corner of the seat.

2. Return the seat to the original position and

by holding the front part of the seat, open
the engine cover slowly toward to rearward.

Cutting-blade cover wash pipe

Engine Cover

Seat

Knob Bolt

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands