Atex AR950 Operation Manual Download Page 83

Page: 83 / 106

How to Work

■

Inspecting/Replacing the Cutting Blade

●

Make sure to stop the engine before inspecting or replacing

the cutting blade.

●

When handling the cutting blade, wear thick gloves to prevent

injury.

●

When replacing the cutting blade, make sure to specify the

manufacturer’s genuine blade. The warranty does not cover any

breakdown or accident resulting from use of a cutting blade other than

manufacturer’s genuine blade.

●

Don’t grind the cutting blade. The blade may break, which brings

a very dangerous situation.

Warning

●

How to Inspect

1. Turn the ignition key to the “Off” position to stop

the engine, and remove the key from the engine
switch.

2. Shift the cutting-height adjustment lever to the

“Start Engine” position.

3. Open the cutting-blade cover after making sure

that the turning of cutting blade stops.

4. Inspect the cutting blade for breakage and wear.

Cutting-height adjustment lever

Start engine

Must be replaced

New blade

Worn blade

Broken blade

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands